Influence of type and content of chemical foaming agent on the dynamic mechanical properties of high density polyethylene-flax fiber composites

Document Type : Research Paper

Authors

1 Assistant Professor, Department of Paper and Packaging Technology, Faculty of Chemistry and Petrochemical Engineering, Standard Research Institute (SRI)

2 Young Researchers and Elite Club, Malayer Branch, Islamic Azad University, Malayer, Iran

Abstract

This study aims to evaluate the influence of type and content of chemical foaming agent on the dynamic mechanical properties of high density polyethylene-flax fiber composites. Composites were prepared via melt mixing in an internal mixer, and then foamed using single-stage batch foaming method. Two type of chemical foaming agents including azodicarbonamide (ADC) and sodium bicarbonate (SB) were considered at three levels of 0, 2 and 4 per hundred resins (phr). The amount of flax fiber and coupling agent for all formulations was fixed at 60% and 2 phr, respectively. Static mechanical tests including flexural and tensile were performed on samples. The dynamic mechanical properties such as storage modulus, loss modulus and damping factor of composites were investigated in the temperature range of -60 to 150 0C at a step of 5 0C and frequency of 1 Hz. Morphology of the samples was also evaluated by scanning electron microscopy (SEM). Results indicate that the chemical foaming agent substantially increased cell size and reduced cell density and mechanical strength of composites. Moreover, the lowest mechanical strength was observed in foamed composites with SB. SEM confirmed that the type and content of chemical foaming agent had significant influence on density reduction of foamed composites. Finally, by increase in the chemical foaming agent content, the storage modulus and loss modulus of samples decreased. However, on addition of chemical foaming agent to composites, the damping factor was increased. Foamed composites prepared with ADC exhibited inferior storage modulus compared than the SB.

Keywords

References

[1] Park, C.B. and Sun, A.H., 2005. Influence of foaming agents on properties of wood flour- polypropylene composites. Journal of Polymer Engineering Science, 38: 212-219.
 [2] Guo, G., Rizivi, G.M. and Park, C.B., 2008. Wood polymer composite foams, Wood Polymer Composites. Woodhead Publishing Ltd, Great Abington, Cambridge, UK , 227-253.
[3] Rizvi, G., Matuana, L.M. and Park, C.B., 2000. Foaming of PS/wood fiber composites in extrusion using moisture as a blowing agent. Journal of Polymer Engineering Science, 40(10): 2124-2132.
[4] Mangeloglu, F. and Matuana, L.M., 2003. Foaming of rigid PVC/wood flour composites though a continuous extrusion process.Vinyl Additives Technology Journal, 9: 26-31.
[5] Bledzki, A.K. and Faruk, O., 2005. Effects of the chemical foaming agents, injection parameters, and melt- flow index on the microstructure and mechanical properties of microcellular injection molded wood fiber/ polypropylene composites. Journal of Applied Polymer Science, 97: 1090-1096.
[6] Kord, B., 2011. Preparation and characterization of lignocellulosic material filled polyethylene composite foams.  Journal of Thermoplastic Composite Materials, 25(8) 917–926.
[7] Bledzki, A.K., Zhang, W. and Faruk, O., 2005. Microfoaming of flax and wood fiber reinforced polypropylene composites.Holz als Roh- und werkstoff, 63: 30-37.
[8] Bledzki, A.K. and Faruk, O., 2006. Effect of chemical foaming agent content on cell morphology and physico-mechanical properties. Journal of Cellular Plastic, 42: 63-76.
[9] Matuana, L.M. and Faruk, O., 2010. the effect of gas saturation conditions on the expansion ratio of microcellular poly (lactic acid)/wood-flour composites.Express Polymer Letters, 4(10): 621–631.
[10] Pourabbasi, S. and Kord, B., 2011. Investigation on the effect of chemical foaming agent and wood flour content on mechanical properties, density and cell morphology of HDPE/EVA/ wood flour hybrid foamed composites. Iranian Journal of Wood and Paper Industries, 2(1): 63-80. (In Persian).
[11] ASTM D E1640., 2013. Standard test method for assignment of the glass transition temperature by dynamic mechanical analysis, American Society of Testing and Materials.
[12] Kord, B., Varshoei, A. and Chamany, V., 2011.  Influence of chemical foaming agent on the physical, mechanical and morphological properties of HDPE/wood flour/nanoclay composites. Journal of Reinforced Plastics and Composites, 30(13): 1115–1124.
[13] Faruk, O., Bledzki, A.K. and Matuana, L.M., 2007. Microcellular foamed wood plastic composites by different process. Macromolecules Material Engineering Journal, 292: 113-117.
[14] Riahinezhad, M., Ghasemi, I., Karrabi, M. and Azizi, H., 2010. An Investigation on the correlation between rheology and morphology of nanocomposite foams based on low density polyethylene (LDPE) and ethylene vinyl acetate (EVA) blends, Journal of Polymer Composite, 31(10): 1808-1816.
[15] Matuana, L.M., Park, C.B. and Balatinecz, J., 1997. Processing and cell morphology relationships for microcellular foamed PVC/wood fiber composites. Journal of Polymer Engineering Science, 38: 212-219.
[16] Pothan, L.A., Oommen, Z. and Thomas S., 2003. Dynamic mechanical analysis of banana fiber reinforced polyester composites. Composite Science Technology, 17: 283–293.
[17] Romanzini, D.,  Ornaghi, H.L, Amico, S.C. and Zattera, A.J., 2012. Influence of fiber hybridization on the dynamic mechanical properties of glass/ramie fiber-reinforced polyester composites. Journal of Reinforced Plastics and Composites, 31(23): 1652–1661.
[18] Devi, L.U., Bhagawan, S.S. and Thomas S., 2010. Dynamic mechanical analysis of pineapple leaf/glass hybrid fiber reinforced polyester composites. Polymer Composite, 31: 956–965.
[19] Pothan, L.A., George, C.N. and John, M.J., 2010. Dynamic mechanical and dielectric behavior of banana-glass hybrid fiber reinforced polyester composites. Journal of Reinforced Plastics and Composites, 29: 1130–1145.
[20] Tajvidi, M., Ebrahimi, G.H. and Enayati, A.A., 2003. Dynamic mechanical analysis of compatibilizer effect on mechanical properties of wood flour-polypropylene composites. Iranian Journal of Natural Resources, 47-59. (In Persian).
[21] Kord, B., Ekrami, M. and Roohani, M., 2014. Effect of nanoclay particles content on the mechanical properties of wood flour-polypropylene composites using dynamic mechanic thermal analysis. Iranian Journal of Wood and Paper Industries, 5(2): 15-26.
[22] Dufresne, A., 2000. Dynamic mechanical analysis of the interphase in bacterial polyester/cellulose whiskers natural composites. Composite Interfaces, 7 (1): 53-67.
Iranian Journal of Wood and Paper Industries
Volume 7, Issue 2 - Serial Number 2
September 2016
Pages 179-191

Files

Share

How to cite

Statistics