Investigation the Plywood Manufacturing of Paulownia (paulownia tomentosa) with Urea and Phenol Formaldehyde Adhesives

Document Type : Research Paper

Authors

Abstract

In recent years, the plywood and veneer industry of Iran has undergone negative growth due to shortage of proper diameter logs and also lack of innovative technologies for the use of low-diameter logs; Moreover, demands for lignocelluloses products has been growing as a consequence of  significant increase in population and expansion of construction Industry, especially in major cities. Hence, it is necessary to cultivate fast-growing species. For this purpose four logs of paulownia (120 cm length and 55 cm diameter) were prepared from the Gorgan shast Kalate forests and then transported to Kosar factory in order to prepare veneers. Produced layers were transferred to the wood laboratory of Gorgan university. Then plywood was manufactured from paulownia species on the basis of the standard 3210 of ISIRI (Institute of Standards and Industrial Researches of Iran) and common tests of plywood were made. The results showed that the mechanical properties of manufactured boards were upper than with standards defined by ISIRI and the physical properties of those manufactured with urea formaldehyde glue were lower than standards which can be considered as negative properties; Albeit, they were not significant and can be disregarded

Keywords


1- امیدی،ا.1378.بررسی تأثیر فاصله کاشت بر خصوصیات آناتومیک چوب پالونیا،پروژه کارشناسی،دانشگاه علوم کشاورزی و منابع طبیعی گرگان، 45 صفحه
2- سجودی، م. حسن عباس، ن.1366 ،پالونیا درخت شگفت انگیز چین، فصلنامه علمی، اجتماعی، اقتصادی جنگل و مرتع(5):20-15
3- اوتادی،ف. 1379، بررسی میزان رشد و خصوصیات چوب پالونیا، مرکز تحقیقات شرکت صنایع چوب و کاغذ مازندران
4- حسینی،ض. افرا،ا.1384. بررسی مشخصات الیاف و ترکیبات شیمیایی پالونیا در منطقه گرگان، مجله منابع طبیعی ایران 58(4): 877-871
5- طبرسا،ت،.فارسی،م.1385.بررسی اثر بهبود دهندگی گونه پالونیا در ساخت تخته خرده چوب از اکالیپتوس. مجله پژوهشی تحقیقات علوم چوب و کاغذ ایران(59).236-225
6- اسدی،م.چمنی گلزار، ع. 1368.مطالعه مهمترین ویژگی های فیزیکی و مکانیکی تخته لایه های تولید شده در ایران. پروژه کارشناسی، دانشکده منابع طبیعی دانشگاه تهران.110 صفحه
7- نوربخش، ا،.کارگرفرد، ا،.گل بابایی، ف.1388. بررسی خواص فیزیکی و مکانیکی تخته خرده چوب ساخته شده از چوب پالونیا. مجله پژوهشی تحقیقات علوم چوب و کاغذ ایران(24).15-25
8- عدالت،ح،.طبرسا،ت،.رئیسی،م.1387.فشرده سازی چوب پالونیا با استفاده از پرس گرم.دو فصلنامه علمی-پژوهشی تحقیقات علوم چوب و کاغذ ایران(23).148-136
9- Ashori,A.,Nourbakhsh,A.2009. Studies on Iranian cultivated paulownia - A potential source of fibrous raw material for paper industry.European Journal of Wood and Wood Products(67). 323-327 pages
10- Akyildiz,M.H.,Kol,H.S.2010.Some technological properties and uses of paulownia(paulownia tomentosa steud)wood. Journal Of Environmental Biology(31). 351-355 pages
11- Kaygin,B.,Guanduz,G.,Aydemir,D.2009.The effect of mass loss mechanic properties of heat – treated paulownia wood.Wood Research(2009). 101-108 Pages
12- Kaygin,B.,Guanduz,G.,Aydemir,D.2009.Some physical of heat-treated paulownia (paulownia elongata) wood.Drying Technology(2009). 89-93 Pages
13- Khaledzade, H. 2001.Investigation on physical and mechanical properties of particleboard from Cameldolensis Eucalyptus and poplar. MSC thesis. Azad university, Tehran science and research unit
14- Heebink, B. G;W. F. Lehmann and K. d. Geimer. 1974. Factors affecting articleboard pressing time. Interaction with catalyst system USDA. For. Serv. Res. Pap. Fpl-208, For. Prod. Lab. Madison, wisconsin.
15- Wang, J;G.Laborie, M and P.Wolcott, M. 2009. Kinetic analysis of phenol-formaldehyde bonded wood joints with dynamical mechanical analysis. Thermochimica Acta (491):58-62
16- Yu- jung, K; Motoaki,O and Yokota, T. 1998. Study on sheet material made from Zephyr strands V: properties of Zephyr board and Zephyr strand lumber using veneer of fast-growing species such as poplar. The Japan Wood Research Society(44): 438- 443