@article { author = {moradpour, payam and Gholizadeh Mehdikhan Mahalleh, amin and Gholamiyan, Hadi}, title = {Evaluation of wood machining parameters and surface quality in cutting process by water jet without abrasive material}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {12}, number = {3}, pages = {429-440}, year = {2021}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {This study aimed at the evaluation of wood machining parameters and surface quality upon using a water jet without abrasive material. Hence, wood species (beech, oak, and poplar), cutting velocity (200, 400 and, 600 m/s), and cutting direction (parallel and perpendicular to the grain) were chosen as variables. After cutting samples with water jet, the samples were scanned from edge and surface using a 1200 dpi scanner. For analyzing the depth of cut and kerf width, Image J software was used. The Surface quality was evaluated using a stylus profilometer, and the surface roughness parameters including Ra and, Rz were measured. The highest and lowest values of depth of cut and kerf width were measured for poplar and beech woods, respectively. According to the results, it can be stated that the cutting direction has a significant effect on the machining parameters so that the maximum depth of cut and the lowest kerf width was observed in the direction parallel to the grain. Also, the results showed that with increasing cutting velocity, the depth of cut increases, and kerf width decreases. The highest and lowest values of surface roughness parameters were observed in poplar (Rz=136/8µ), and beech (Rz=115/62µ) woods, respectively. Based on the results, it can be concluded that high-speed machining in woods with dense texture and parallel to grain can improve the surface quality in water jet cutting.}, keywords = {Water jet,Cutting velocity,Cutting direction,Depth of cut,Kerf width,Surface roughness}, title_fa = {ارزیابی پارامترهای ماشین‌کاری چوب و کیفیت سطح در فرآیند برش با جت‌آب بدون ماده ساینده}, abstract_fa = {هدف از تحقیق، ارزیابی پارامترهای ماشین‌کاری چوب و کیفیت سطح در فرآیند برش با جت‌آب بدون ماده‌ساینده بود. بدین منظور نوع گونه چوبی (راش، بلوط و صنوبر)، سرعت برش (200، 400 و 600 متر بر ثانیه) و همچنین جهت برش (موازی و عمود بر الیاف) به‌عنوان عوامل متغیر تحقیق انتخاب شدند. پس از برش نمونه‌ها با جت‌آب، تصویربرداری از سطح و لبه‌ نمونه‌ها در محل برش توسط اسکنر با وضوح dpi1200 انجام شد. برای اندازه‌گیری عمق و شکاف‌برش در تصاویر بدست‌آمده، از نرم‌ افزار Image Jاستفاده شد. کیفیت سطح با استفاده از زبری‌سنج سوزنی ارزیابی شد و پارامترهای زبری سطح شامل Ra و Rz اندازه‌گیری شدند. بیشترین و کمترین مقادیر عمق و شکاف‌برش به ترتیب برای چوب صنوبر و چوب راش اندازه‌گیری شد. با توجه به نتایج می‌توان اظهار داشت که جهت برش تاثیر قابل‌ملاحظه‌ای روی پارامترهای برش دارد، به‌طوری‌که بیشترین عمق و کمترین شکاف‌برش در جهت موازی الیاف مشاهده شد. همچنین نتایج نشان دادند با افزایش سرعت برش، عمق‌برش افزایش یافته و شکاف‌برش کاهش می‌یابد. بیشترین و کمترین مقادیر پارامترهای زبری‌سطح به ترتیب در چوب صنوبر(80µ/136=Rz) و چوب راش(62µ/115=Rz) مشاهده شد. بر اساس نتایج حاصله می‌توان نتیجه‌گیری کرد، ماشین‌کاری با سرعت بالا در چوب‌های با بافت متراکم و در راستای موازی الیاف می تواند منجر به بهبود کیفیت‌ سطح در برش با جت‌آب ‌گردد.}, keywords_fa = {جت‌آب,سرعت برش,جهت برش,عمق‌برش,شکاف‌برش,زبری‌سطح}, url = {https://www.ijwp.ir/article_248511.html}, eprint = {https://www.ijwp.ir/article_248511_89eb7864fedcf360ffe501f55798670b.pdf} }