Fabrication and properties evaluation of three layered transparent nanocomposite reinforced with cellulose and chitin nanofibers

Document Type : Research Paper

Authors

1 Ph.D. student, Department of wood engineering and technology, Gorgan university of agricultural sciences and natural resources, Gorgan, Iran

2 Assoiciate Prof., Department of wood engineering and technology, Gorgan university of agricultural sciences and natural resources, Gorgan, Iran

3 Assistant Prof., Department of wood engineering and technology, Gorgan university of agricultural sciences and natural resources, Gorgan, Iran

Abstract

Abstract
In this study, three-layered transparent nanocomposite containing wood cellulose nanofibers (WCNF), bacterial cellulose nanofiber (BCNF) and chitin nanofibers (ChNF) individually as core layer and epoxy as top and bottom layers has been fabricated and characterized. The WCNF, BCNF and ChNF were first converted to nanofilms, followed by solvent exchanging by ethanol and acetone and then immersed into epoxy resin. The impregnated nanofilms with epoxy was cold pressed followed by drying in an oven to get three layered nanocomposites. FE-SEM, transparency and tensile test showed that epoxy could penetrate into the core layer (nanofilms) positively affected the transparency and mechanical properties. The crystallinity index of nanocomposite was lower than that of pure nanofilms. ATR-FTIR confirmed the peaks of nanocomposites were similar to those of epoxy. The mechanical and transparency properties of nanocomposite were higher than those of pure nanofilms. Nanocomposite containing BCNF and ChNF showed highest tensile strength and transparency, respectively.

Keywords

Main Subjects


[1] Shams, M.I. and Yano, H., 2015. Doubly curved nanofiber-reinforced optically transparent composites. Scientific reports, 5:16421.
[2] Yousefi, H., Nishino, T., Faezipour, M., Ebrahimi, G. and Shakeri, A., 2011. Direct fabrication of all-cellulose nanocomposite from cellulose microfibers using ionic liquid-based nanowelding. Biomacromolecules, 12(11): 4080-4085.
[3] Jonoobi, M., Oladi, R., Davoudpour, Y., Oksman, K., Dufresne, A., Hamzeh, Y. and Davoodi, R., 2015. Different preparation methods and properties of nanostructured cellulose from various natural resources and residues: a review. Cellulose, 22(2):935-969.
[4] Yousefi, H., Azad, S., Mashkour, M. and Khazaeian, A., 2018. Cellulose nanofiber board. Carbohydrate polymers, 187: 133-139.
[5] Nogi, M., Handa, K., Nakagaito, A. N. and Yano, H., 2005. Optically transparent bionanofiber composites with low sensitivity to refractive index of the polymer matrix. Applied Physics Letters, 87(24):243110.
[6] Fang Z., Zhu, H., Yuan, Y., Ha, D., Zhu, S., Preston, C. and Chen, G., 2014. Novel nanostructured paper with ultrahigh transparency and ultrahigh haze for solar cells. Nano letters, 14(2):765-773.
[7] Fernandes, S. C., Oliveira, L., Freire, C. S., Silvestre, A. J., Neto, C. P., Gandini, A. and Desbriéres, J., 2009. Novel transparent nanocomposite films based on chitosan and bacterial cellulose. Green Chemistry, 11(12): 2023-2029.
[8] Tummala, G. K., Rojas, R. and Mihranyan, A., 2016. Poly (vinyl alcohol) Hydrogels Reinforced with Nanocellulose for Ophthalmic Applications: General Characteristics and Optical Properties. The Journal of Physical Chemistry B, 120(51):13094-13101.
[9] Shao, X., Li, D. G., Li, A. J. and Gu, W. B., 2013. Chitin Nanofibers/Epoxy Resin Optically Transparent Nanocomposite Films. In Advanced Materials Research (Vol. 602, pp. 1479-1483). Trans Tech Publications.
[10] Eichhorn, S. J., Dufresne, A., Aranguren, M., Marcovich, N. E., Capadona, J. R., Rowan, S. J. and Gindl, W., 2010. current international research into cellulose nanofibres and nanocomposites. Journal of materials science, 45(1): 1.
[11] Henriksson, M., Berglund, L. A., Isaksson, P., LindstroĢˆm, T. and Nishino, T., 2008. Cellulose nanopaper structures of high toughness. Biomacromolecules, 9(6): 1579-1585.
[12] Segal, L. G. J. M. A., Creely, J. J., Martin Jr, A. E. and Conrad, C. M., 1959. An empirical method for estimating the degree of crystallinity of native cellulose using the X-ray diffractometer. Textile Research Journal, 29(10):786-794.
[13] Ifuku, S., Morooka, S., Nakagaito, A. N., Morimoto, M. and Saimoto, H., 2011. Preparation and characterization of optically transparent chitin nanofiber/(meth) acrylic resin composites. Green Chemistry, 13(7), 1708-1711.
[14] Zhang, Z., Wang, H., Li, S., Li, L. and Li, D., 2015. Transparent and flexible cellulose nanofibers/silver nanowires/acrylic resin composite electrode. Composites Part A: Applied Science and Manufacturing, 76: 309-315.
 [15] Iwamoto, S., Nakagaito, A. N.and Yano, H., 2007. Nano-fibrillation of pulp fibers for the processing of transparent nanocomposites. Applied Physics A, 89(2): 461-466.
[16] Yousefi, H., Faezipour, M., Hedjazi, S., Mousavi, M. M., Azusa, Y. and Heidari, A. H., 2013. Comparative study of paper and nanopaper properties prepared from bacterial cellulose nanofibers and fibers/ground cellulose nanofibers of canola straw. Industrial Crops and Products, 43: 732-737.
[17] Bhagat, S. and Verma, P. K., 2013. Effect of Filler Parameter on Morphology of Graphite Filled Epoxy Composites. International Journal of Scientific & Engineering Research, 4 (4): 459.
[18] Hu, W., Chen, S., Yang, Z., Liu, L. and Wang, H., 2011. Flexible electrically conductive nanocomposite membrane based on bacterial cellulose and polyaniline. The Journal of physical chemistry B, 115(26), 8453-8457.
[19] Chang, P. R., Jian, R., Yu, J. and Ma, X., 2010. Starch-based composites reinforced with novel chitin nanoparticles. Carbohydrate polymers, 80(2): 420-425.
[20] Cárdenas, G., Cabrera, G., Taboada, E. and Miranda, S. P., 2004. Chitin characterization by SEM, FTIR, XRD, and 13C cross polarization/mass angle spinning NMR. Journal of Applied Polymer Science, 93(4):1876-1885.
[21] Ansari, F., Lindh, E. L., Furo, I., Johansson, M. K. and Berglund, L. A., 2016. Interface tailoring through covalent hydroxyl-epoxy bonds improves hygromechanical stability in nanocellulose materials. Composites Science and Technology, 134, 175-183.