1دانشجوی دکتری، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران، کرج، ایران
2استاد، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران، کرج، ایران
3استادیار گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران، کرج، ایران
4استادیار دانشگاه مین، امریکا
چکیده
این پژوهش با هدف بررسی ظرفیت لنگر خمشی اتصال با پین چوبی در تختهچندلا صورت گرفته است. اعضای اتصال از تختهچندلا با ضخامت 19 میلیمتر و ساختهشده از گونههای پهنبرگ (راش، ممرز و توسکا) بودند. در این بررسی، تأثیر متغیرهای گونه چوب پین (راش و ممرز)، قطر پین در سه سطح 6، 8 و 10 میلیمتر و عمق نفوذ در سه سطح 9، 13 و 17 میلیمتر، بر ظرفیت لنگر خمشی اتصالهای T شکل بررسیشده است. نتایج نشان دادند که ظرفیت لنگر خمشی اتصال با افزایش قطر و عمق نفوذ پین افزایش مییابد. ظرفیت لنگر خمشی اتصالهای ساختهشده با پین راش در مقایسه با اتصالهای ساختهشده با پین ممرز بیشتر است. بالاترین میزان ظرفیت لنگر خمشی ( N.m29/44) مربوط به پین راش با قطر 10 میلیمتر و عمق نفوذ 17 میلیمتر بوده است. کمترین میزان ظرفیت لنگر خمشی (N.m08/12) در پین ممرز با قطر 6 میلیمتر و عمق نفوذ 9 میلیمتر دیدهشده است.
[1] Ebrahimi, G. 2007. Engineering design of furniture structure. Tehran university publication, 491 pp. (In Persian).
[2] Jones, A. and Lutes, R. 1993. Handbook of joinery. New York, USA: Sterling Press, 144 p.
[3] Eckelman, C. A. 2003. Textbook of product engineering and strength design of furniture. West Lafayette (IN): Purdue University Press.
[4] Tankut, A. N. and Tankut, N. 2009. Investigations the effects of fastener, glue, and composite material types on the strength of corner joints in case–type furniture construction. Material Design, 30:4175–82.
[5] Said, A. Ashaari, H. Roslan, A. Hilmi, M. (1993). Withdrawal and bending strength of dowel from three Malasian timbers. Journal of tropical forest science, 6(1): 74-80.
[6] Chou, C. and Hes, C. (1998). Effect of hygroscopic treatments on bending strength of dowel joints. Adhesive technology and bonded tropical wood products, 96: 602-605.
[7] Norvydas, V. Juodeikiene, I. Minelga, D. 2005. The Influence of Glued Dowel Joints Construction on the Bending Moment Resistance. Materials science, 11(1): 36-39.
[8] Zhang, J. and Eckelman, C.A. (1993). Rational design of multi- dowel corner joints in case construction. Forest produsts Journal, 43(11): 52-58.
[9] Tankut, A.N. 2005. Optimum dowel spacing for corner joints in 32 mm cabinet construction. Forest Produsts Journal, 55(12):100–4.
[10] Uysal, B. and Ozcifci, A. 2003. Effects of dowels produced from various materials on withdrawal strength in mdf and pb. Journal of Applied Polymer Science, 88: 531–535.
[11] Tas, H. H. 2010. Strength properties of L–profiled furniture joints constructed with laminated wooden panels. Scientific Research and Essays, 5 (6): 545–50.
[12] Ghofrani, M. and Noori, H. 2005. Lateral holding strength of wooden dowel, screw and ready-to-assemble joints (RTA joints) constructed of Medium Density Fiberboard (MDF). Journal of Forest and Wood Products, 24(2): 219-231. (In Persian).
[13] Bahmani, M., Ebrahimi, G., Fathi, L. 2009. Predicting of Withdrawal Strength With Dowel Joint in Medium Density Fiber (MDF) By mathematic model. Iranian Journal of Wood and Paper Science Research, 24(1): 117-124. (In Persian).
[14] Bahmani, M., Ebrahimi, GH., Veisi, J. 2009. Design of experimental model for predicting ultimate bending strength dowel joint in medium density fiber. Journal of forest and wood products (JFWP), 62(4): 335-342. (In Persian).
[15] Standard Test Methods for Small Clear Specimens of Timber. Annual Book of ASTM Standard, D 143. 2000.
[16] Standard Test Methods for Specific Gravity of Wood and Wood–Base Materials, Annual Book of ASTM Standard, D 2395, 1999.
[17] Eckelman, C. A. 2004. Engineering Design of furniture. Purdue Uni.UsA, Chap 6.
[18] Zhang, J. L. and Eckelman, C. A. 1993. The bending moment resistance of single–dowel corner joints in case construction. Forest Produsts Journal, 43(6):19–24.