Design, Construction, and Performance Analysis of a Wood Thermal Conductivity Measurement Device using Flat Plate Heat Pipes

Document Type : Research Paper

Authors

Abstract

In this paper, the design, construction, and performance analysis of a wood thermal conductivity measurement device using flat plate heat pipes has been experimentally studied. The device was designed to measure the thermal conductivity of wood in various ranges of temperature. Thermal conductivity of hornbeam (Carpinus betulus) has been measured at various temperatures between 40-80 ºC and a relationship has been recommended for the sample. The results show that the thermal conductivity of this species increases linearly with temperature. Also, it has been concluded that flat plate heat pipes distribute heat flux on the surface of the wood uniformly leading to a faster steady state condition, which can reduce time of the test and result in energy saving and more accurate results.

Keywords


1- Steinhagen, H. Peter, 1977, Thermal Conductive Properties of Wood, Green or Dry, from to  A Literature Review, General Technical Report, FPL-9.
2- Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus (C 518-04), Book of ASTM Standards, 04.06, D 10.1520/C0518-04,2010
3- Method of Test for Thermal Conductivity of Materials by Means of the Guarded Hot Plate (C 177-45), ASTM Standards ,Part 3:1084, 1955
4- Clarke, L.N. and R.S.T. Kingston. 1950. Equipment for the simultaneous determination of thermal conductivity and diffusivity of insulating materials using a variable-state method. Australian Journal of Applied science, Vol.1(2):172-187
5- Gu, H., Hunt, J. F., 2007, Two-dimensional finite element heat transfer model of softwood. Part III. Effect of moisture content on thermal conductivity, Wood and Fiber Science, 39(1), pp.159-166
6- Ngohe-Ekam, P.S., Meukam, P., 1, Menguy, G., Girard, P., 2006,Thermophysical characterization of tropical wood used as building materials: With respect to the basal density, Construction and Building Materials, 20, pp. 929–938
7- Method of Test for Thermal Conductivity of Materials by Hot Wire , ASTM Standards ,Part 3:1084, 1955
8- Basiulis, A., Tanzer, H., and McCabe, S., 1986, Thermal Management of High Power PWB’s through the Use of Heat Pipe Substrates, in: Sixth Annual International Electronics Packaging Conference, San Diego, CA, USA, vol. 6, p. 501
9- Rightley, M.J., Tigges, C.P., Givler, R.C., Robino, C.V., Mulhall, J.J., and Smith, P.M., 2003, Innovative Wick Design for Multi-source Flat Plate Heat Pipes, Microelectronics Journal, Vol. 34, pp. 187–194
10- Thomson, M., Ruel, C., and Donato, M., 1989,Characterization of a Flat Plate Heat Pipe for Electronic Cooling in a Space Environment. In: proceeding of National Heat Transfer Conference, Heat Transfer in Electronics HTD-Vol. 111, pp. 59–65
11- Ojen, H., and Hoogendoorn, C. J. , 1979, Vapor Flow Calculations in a Flat-plate Heat Pipe, AIAA Journal, Vol. 17, pp.1251-1259
12- Vafai, K., and Wang, W., 1992, Analysis of Flow and Heat Transfer Characteristics of an Asymmetrical Flat Plate Heat Pipe, International Journal of Heat Mass Transfer, Vol.35, pp. 2087-2099
13- Vafai, K., and  Zhu, N. , 1995, and Wang, W., Analysis of Asymmetrical Disk-shaped and Flat-plate Heat Pipes, ASME Journal of Heat Transfer, Vol.117, pp. 209-218
14- Zhu, N., Vafai, K., 1998, Vapor and Liquid Flow in an Asymmetrical Flat Plate Heat Pipe: a Three-dimensional Analytical and Numerical Investigation, Int. Journal of Heat Mass Transfer, Vol.41, pp. 159-174
15- Zhu, N., and Vafai, K. , 1998, Analytical Modeling of the Startup Characteristics of Asymmetrical Flat Plate and Disk-shaped Heat Pipes, Int. J. of Heat and Mass transfer, Vol.41, pp. 2619-2637
16- Wang, Y., and Vafai, K. , 2000, Transient Characterization of Flat Plate Heat Pipes During Startup and Shutdown Operations, Int. J. of Heat  and Mass Transfer, Vol.43, pp.2641-2655