@article { author = {Edalat, Hamidreza and Afshari, Reza and Khazaeian, Abolghasem and Rasouli, Davoud}, title = {Effect of species type and sanding sequence on the adhesion strength and the interphase region of Polyurethane coating and veneer}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {11}, number = {2}, pages = {317-332}, year = {2020}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The purpose of this research was the investigation of sanding sequence and coating thickness effect on adhesion strength of coating in two species: beech and elm. For this purpose, beech and elm veneers with 0.6 mm thickness were laminated on MDF with 16 mm thickness by UF and hot press. The surface of the laminated panels was sanded by two different sequences; the soft (180-280 grits) and rough (150-180 grits) one. Before the coating application, the surface was sanded with 400 grits. Then they were coated with polyurethane in two forms of one and two-layered coating. After that, the adhesion strength test was done on specimens according to ASTM D4541. To have a more precise investigation of the interphase region of coating-veneer, photomicrographs were captured by fluorescent microscopy to analyze and calculate the effective penetration parameter of the coating into the wood texture. The results showed that two species respond to sanding sequences differently and a thicker coating layer increased the adhesion strength. Beech as a diffuse-porous wood had the finer texture and higher density compared with elm. Therefore, the adhesion strength of the beech veneer was declined by 13.8 % and reaches 2.59 MPa due to the use of a rough sanding sequence. However, these sequences caused the opposite result in elm veneer and led to a 25.7 % adhesion improvement (3.23 MPa). The study on microphotographs and the effective penetration parameter stated that an even thickness of the coating layer and effective penetration reduction has been possible when the rough sequence and soft one are applied on elm and beech, respectively.}, keywords = {Adhesion Strength,Interphase region,Polyurethane coating,Veneer,Sanding sequence}, title_fa = {تأثیر نوع گونه و توالی پرداخت بر مقاومت چسبندگی و ناحیه اینترفاز پوشش پلی اورتان و روکش طبیعی چوب}, abstract_fa = {هدف از این تحقیق بررسی تأثیر توالی پرداخت و ضخامت پوشش بر مقاومت چسبندگی آن در دو گونه راش و ملج بود. برای این منظور روکش­های راش و ملج با ضخامت 6/0 میلی‌متر با استفاده از چسب اوره فرم آلدئید و پرس گرم بر روی تخته فیبر دانسیته متوسط با ضخامت 16 میلی‌متر روکش‌کاری شدند. سطح پانل­های روکش شده به­وسیله کاغذهای سنباده با دو نوع توالی پرداخت نرم (280-180) و زبر (180-150) پرداخت شدند. پیش از اعمال پوشش، پرداخت نهایی با سنباده درجه 400 انجام گردید. سپس با استفاده از پوشش پلی اورتان سطح محصولات به‌صورت تک لایه و دولایه پوشش داده شد. سپس آزمون چسبندگی پوشش طبق استاندارد ASTM D4541 بر روی نمونه­ها انجام گردید. به‌منظور بررسی دقیق­تر ناحیه اینترفاز پوشش-روکش، تصاویری به کمک میکروسکوپ فلوئورسنت جهت آنالیز و محاسبه نفوذ مؤثر پوشش پلی اورتان به دورن بافت چوب تهیه شدند. نتایج نشان دادند که دو گونه پاسخ­های متفاوتی نسبت به توالی­های پرداخت نشان می­­دهند و افزایش ضخامت پوشش نیز در اغلب موارد مقاومت چسبندگی را بهبود می­دهد. روکش راش به‌عنوان یک‌گونه پراکنده آوند نسبت به ملج با ساختار بخش روزنه­ای، تراکم بیشتر و بافت ریزتری داشت و به همین دلیل در اثر اعمال توالی پرداخت زبر مقاومت چسبندگی پوشش آن 8/13 درصد کاهش یافت و به 59/2 مگا پاسکال رسید ولی توالی مذکور در روکش ملج نتیجه عکس داشت و موجب بهبود چسبندگی به میزان 7/25 درصد و رسیدن آن به مقدار 23/3 مگا پاسکال گردید. بررسی تصاویر میکروسکوپی و پارامتر نفوذ مؤثر نیز بیانگر این نکته بود که دستیابی به ضخامت یکنواخت پوشش و کاهش نفوذ مؤثر آن برای گونه ملج در توالی پرداخت زبر و برای راش در توالی نرم ممکن می­­گردد.}, keywords_fa = {مقاومت چسبندگی,ناحیه اینترفاز,پوشش پلی اورتان,روکش طبیعی,توالی پرداخت}, url = {https://www.ijwp.ir/article_38024.html}, eprint = {https://www.ijwp.ir/article_38024_714f0fff21e99557f309dc426b07718b.pdf} }