@article { author = {Rostampour haftkhani, akbar}, title = {Experimental study on flexural performance of poplar glued-laminated timber constructed by mechanical fastener and comparing them with those made with cold press}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {10}, number = {3}, pages = {347-360}, year = {2019}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this study, modulus of rupture (MOR) and modulus of elasticity (MOE) of glued-laminated timber (Glulam) made out of poplar (Populus alba) with galvanized steel nail, brad strip nail, coarse thread drywall screw for applying pressure were investigated and compared with those constructed with cold press. Amount of polyurethane adhesive was 300 g/m2. Thickness, width and span of 3-ply glulam specimens were 57, 80 and 640 mm, respectively. Static bending test was performed according to ASTM D 7341 by Instron testing machine. The results showed that the higher MOR and MOE were related to Glulam connected by 4 screws on 8×8 cm2 with adhesive (69.3 MPa), and those connected by 2 galvanized steel nail with adhesive (6737.7 MPa), respectively. The results also revealed that the lower MOR and MOE were both observed in Glulam connected by 2 brad strip nail without any adhesive (23.9 and 1252.7 MPa, respectively). The results showed that MOR and MOE of glulam were changed with the independent variation of number of fastener 3.7 and ˂1%, respectively. The higher variation was related to independent effect of adhesive (130 and 317.8% for MOR and MOE, respectively). Analysis of variance indicated that only the independent effect of adhesive application was only statistically significant at 95% confidence level. The comparison of MOR and MOE of Glulam made with two fasteners with those constructed by cold press showed that there was not significant difference between them. So, the use of galvanized steel nail, brad strip nail, coarse thread drywall screw for applying pressure to manufacture Glulam instead of cold press is possible and the best item was brad strip nail due to easy application and installation by pneumatic nailer and low cost.}, keywords = {Flexural performance,glued laminated timber (Glulam),Poplar,mechanical fastener,cold press}, title_fa = {مطالعه تجربی مقاومت خمشی تیر لایه ای (گلولام) ساخته شده از گونه صنوبر با اتصال دهنده های مکانیکی و مقایسه آنها با گلولام ساخته شده با پرس سرد}, abstract_fa = {این مطالعه با هدف بررسی مقاومت خمشی (MOR) و مدول الاستیسیته خمشی (MOE) تیر لایه‌ای (گلولام) ساخته شده از صنوبر (Populus alba) با اتصال‌دهنده‌های مکانیکی مانند میخ فولادی گالوانیزه، میخ شانه‌ای و پیچ پانلی رزوه درشت و نیز با و بدون چسب و مقایسه آنها با گلولام ساخته شده با پرس سرد انجام شد. چسب مورد استفاده پلی‌اورتان و مقدار مصرف آنg/m2 300 بود. ضخامت، پهنا و طول دهانه گلولام‌های سه‌لایه برای آزمون خمش به‌ترتیب 57، 80 وmm 640 بود. آزمون خمش براساس ASTM D7341 و با دستگاه اینسترون انجام شد. نتایج نشان داد که بیشترین MOR و MOE به‌ترتیب مربوط به گلولام‌های ساخته شده با چهار عدد پیچ در سطح 8× cm28 به همراه چسب (MPa 3/69) و دو عدد میخ فولادی به همراه چسب ( MPa7/6737) بود. همچنین نتایج نشان داد که کمترین MOR و MOE هردو مربوط به گلولام‌های ساخته شده با دو عدد میخ شانه‌ای بدون چسب بود (به‌ترتیب 9/23 و MPa7/1252). نتایج نشان داد که با تغییر مستقل تعداد اتصال‌دهنده MOR و MOE به‌ترتیب 7/3 و کمتر از یک درصد تغییر کرد. بیشترین تغییرات مربوط به تاثیر مستقل کاربرد چسب بوده است (130درصد برای MOR و 8/317 درصد برای MOE). تجزیه و تحلیل آماری نشان داد که فقط تأثیر مستقل کاربرد چسب بر MOR و MOE در سطح اعتماد 95درصد از نظر آماری معنی‌دار است. نتایج مقایسه MOR و MOE گلولام‌های ساخته شده با تیمارهای ساخته شده با دو اتصال‌دهنده و چسب در مقایسه با پرس سرد نشان داد که هیچ اختلاف معنی‌داری بین آنها وجود ندارد، از‌این‌رو، می‌توان از پیچ، میخ فولادی و شانه‌ای برای ساخت گلولام استفاده کرد، که از بین آنها میخ‌شانه‌ای به دلیل سهولت کاربرد و نصب آن با میخکوب بادی و هزینه کمتر بهترین گزینه است.}, keywords_fa = {مقاومت خمشی,تیر لایه‌ای (گلولام),صنوبر,اتصال‌دهنده‌های مکانیکی,پرس سرد}, url = {https://www.ijwp.ir/article_36318.html}, eprint = {https://www.ijwp.ir/article_36318_4c09583c842fc05d3869064ea746008f.pdf} }