@article { author = {Rostampour-Haftkhani, Aَkbar and sharari, mearaj and arabi, mohammad and Hajializadeh, Farajolah}, title = {Improvement of the bending moment capacity of mitered MDF frame under diagonal tension by using of the densified poplar dowel}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {12}, number = {4}, pages = {561-573}, year = {2022}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The aim of this study was to improve the joints of the mitered furniture frames by using the densified poplar dowels (Populus alba) instead of beech dowels. Therefore, the effects of the dowel number (one and two dowels), dowel diameter (8, 10, and 12mm), and compression ratio (0, 15, and 30%) on bending moment capacity of L-shaped frame corner joints constructed of medium-density fiberboard (MDF) under diagonal tension load were investigated. Then, their performance was compared with those manufactured with beech dowels. Polyvinyl chloride (PVA) was used for gluing the joints. Diagonal loading was performed by Hounsfield (model No. 0380) testing machine with a 5 mm/min loading rate. The results revealed that the bending moment capacity of joints was increased 105.5, 54.3, and 28.75% respectively with the increase of the dowel number, dowel diameter, and compression ratio. The highest bending moment capacity was observed in the joints made out of two 30% compressed dowels with a diameter of 10 mm, and the least of them were seen in joints constructed of one uncompressed dowel with a diameter of 8 mm. the comparison of the joints dowelled by poplar with beech showed that the difference among the bending moment capacity of joints made of poplar dowels with 30% compression ratio and beech dowels was very small (less than one percent), which indicates usability of the densified poplar dowels instead of beech ones.}, keywords = {corner joints,MDF frame,densified poplar dowel,bending moment capacity}, title_fa = {بهبود ظرفیت لنگر خمشی اتصال‌های فارسی قاب ساخته‌شده با MDF تحت بار کشش قطری با استفاده از پین فشرده صنوبر}, abstract_fa = {هدف از این تحقیق، بررسی تقویت اتصال فارسی قاب‌های مبلمان با استفاده از پین فشرده صنوبر (Populus alba) به جای پین راش است. از این‌رو، تاثیر تعداد پین چوبی مورد استفاده (یک و دو)، قطر پین چوبی (8، 10 و 12 میلیمتر) و درصد فشردگی پین صنوبر (صفر، 15 و 30 درصد) بر ظرفیت لنگر خمشی اتصال‌های گوشه‌ای L شکل ساخته شده از تخته فیبر با دانسیته متوسط (MDF) زیر بار کشش قطری مورد بررسی قرار گرفت. سپس ظرفیت لنگر خمشی آنها با اتصال‌‌های ساخته شده با پین چوب راش مورد مقایسه قرار گرفت. برای چسباندن اتصال‌ها از چسب پلی وینیل استات استفاده شد. بارگذاری کشش قطری روی اتصال‌ها با دستگاه Hounsfield مدل 0308 با سرعت mm/min 5 انجام شد. نتایج نشان داد که با افزایش تعداد پین، قطر پین و درصد فشردگی میانگین ظرفیت لنگر خمشی اتصال به ترتیب 5/105، 3/54 و 75/28 درصد افزایش یافته است، که از نظر آماری معنی‌دار بود. بیشترین ظرفیت لنگر خمشی مربوط به اتصال ساخته شده با دو عدد پین با قطر 10 میلیمتر با 30 درصد فشردگی (N.m 12/43) و کمترین آن مربوط به اتصال ساخته شده با یک پین با قطر 8 میلیمتر بدون فشردگی (N.m 03/11) دیده شده است. مقایسه اتصال‌های ساخته شده با پین فشرده صنوبر با پین راش نشان داد که ظرفیت لنگر اتصال‌های ساخته شده با پین‌های صنوبر با 30 درصد فشردگی نسبت به پین‌های راش اختلاف ناچیزی داشتند (کمتر از یک درصد)، که بیانگر قابلیت استفاده از پین فشرده صنوبر به جای پین راش است.}, keywords_fa = {اتصال گوشه‌ای,قاب MDF,پین فشرده صنوبر,ظرفیت لنگر خمشی}, url = {https://www.ijwp.ir/article_251259.html}, eprint = {https://www.ijwp.ir/article_251259_6f7e1d599dec6f4414b83325ef93b672.pdf} }