@article { author = {اسماعیلی, ندا and قربانی, مریم and beparva, pouriya}, title = {Comparison the performance of different catalysts in chemical modification of Poplar wood with Glutaraldehyde}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {7}, number = {3}, pages = {363-375}, year = {2016}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this study, the effect of different catalysts on chemical modification of poplar wood and physical properties of the resulting product was evaluated. 12.5% HCl and water soluble salts containing ZnCl2, CaCl2, AlCl3, MgCl2 (based on the weight of glutaraldehyde) and 1% Al2O3, SiO2 and ZnO nano particles (based on the weight of glutaraldehyde) were used. After heating in oven for 48 hour, modification with glutaraldehyde and MgCl2, ZnO nano particles, SiO2, Al2O3, ZnCl2, AlCl3, CaCl2 and HCl as catalysts were resulted to 14.5, 12.57, 10.62, 8.69, 8.51, 7.19, 5.97 and 5.41 % weight gain respectively. After 24h soaking in water, the physical properties of modified specimens, such as water absorption, volume swelling and ASE were measured. The highest and lowest bulking were calculated for Mgcl2 and Hcl catalysts with 6.98 and 2.37% respectively. The modification in presence of Mgcl2 catalyst was shown highest increase of density with average of 0.55 g/cm3. The highest and lowest water absorption was measured 79.61 and 45.32% in the modification with HCl and MgCl catalysts. Hcl with acidic quality, can break ether bonds in hemiacetal and even acetal structure. Modification with MgCl2 was shown best result in comparison with other catalysts. It is likely that the formation a complex of magnesium with oxygen, could resulted to activate carbonyl groups in glutaraldehyde and created the crosslink.}, keywords = {Glutaraldehyde,Chemical modification,catalysts,physical properties,Weight percent gain}, title_fa = {مقایسه عملکرد کاتالیزورهای مختلف در اصلاح شیمیایی چوب صنوبر با گلوتارآلدئید}, abstract_fa = {در این پژوهش اثر کاتالیزورهای مختلف در اصلاح شیمیایی چوب صنوبر با گلوتارآلدئید و خواص فیزیکی فرآورده حاصل مورد بررسی قرار گرفتند. اسید هیدروکلریک و نمک‌های محلول در آب کلریدروی، کلریدکلسیم، کلریدآمونیوم، کلریدمنیزیم به میزان 5/12 درصد و نمک‌های اکسید‌آلومینیوم، اکسید‌سیلیس و نانوکسیدروی به میزان 1درصد برمبنای وزن گلوتارآلدئید استفاده شدند. پس از 48ساعت گرمادهی در آون، افزایش‌وزن ناشی از اصلاح برای کاتالیزورهای کلریدمنیزیم، نانوکسید‌روی، اکسید‌سیلیس، اکسیدآلومینیوم، کلریدروی، کلریدآمونیوم، کلریدکلسیم و اسیدهیدروکلریک به‌ترتیب 15/14، 57/12، 62/10، 69/8، 51/8، 19/7، 97/5 و 41/5درصد محاسبه شدند. خواص فیزیکی نمونه‌های اصلاح شده از جمله جذب آب، واکشیدگی حجمی و کارایی ضدواکشیدگی متعاقب 24 ساعت غوطه‌وری در آب محاسبه‌گردید. بیش‌ترین و کم‌ترین میزان حجیم‌کنندگی در سطح اصلاح‌شده با کلرید‌منیزیم به مقدار 98/6 و اسید‌هیدروکلریک با میانگین 37/2درصد اندازه‌گیری‌شد. دانسیته‌ی سطح حاوی کاتالیزور کلرید-منیزیم با میانگین g/cm3 55/0، بیشترین افزایش را نسبت به شاهد نشان‌داد. در مقایسه بین سطوح اصلاح، بیشترین و کمترین جذب آب در سطح اصلاح‌شده با کاتالیزور اسید‌هیدروکلریک به مقدار 61/79درصد و سطح حاوی کاتالیزور کلرید‌منیزیم با میانگین 32/45 درصد محاسبه‌گردید. اسیدهیدروکلریک به علت خاصیت اسیدی می‌تواند موجب شکسته شدن پیوندهای اتری ساختار همی-استال و حتی استال گردد. سطح اصلاح‌شده با کاتالیزور کلرید‌منیزیم در مقایسه با سایر کاتالیزورهای مورد استفاده، بهترین نتیجه را نشان داد. این احتمال وجود دارد که منیزیم طی تشکیل کمپلکس با اکسیژن، باعث فعال‌شدن گروه‌های کربونیل گلوتارآلدئید و تشکیل پیوندهای عرضی شود.}, keywords_fa = {گلوتارآلدئید,اصلاح شیمیایی,کاتالیزور,خواص فیزیکی,افزایش‌وزن}, url = {https://www.ijwp.ir/article_19231.html}, eprint = {https://www.ijwp.ir/article_19231_982242a0d8c321cfe76e33932357fc8c.pdf} }