@article { author = {Faezipour, M.Mahdi and Naghizadeh, Zahra and Ebrahimi, Ghanbar and Hamzeh, Yahya}, title = {Investigation on Effect of Additives on Thermal Conductivity of Herbaceous Fiber Reinforced Cement Composite}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {3}, number = {2}, pages = {39-52}, year = {2013}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this research, fiber reinforcement cement composites (A and B) with low thermal conductivity were produced. Composites type B were produced by two levels of fibers (Equisetum telmateia), 15 and 25%, three levels of silica fume gel, 0, 7 and 10% and three levels of fly ash, 0, 20 and 30%. In composites type A fly ash was replaced by aluminium powder in three levels, 0, 0.08 and 0.1% (all percentage by weight) to manufacture composites with target density and thickness of 1.10 g/cm3 and 13 mm respectively. Results of tests to determine effects of additives on thermal conductivity of mentioned composites have shown that the increasing amount of each of the mentioned additives would significantly affect thermal conductivity of the experimental composites. Least thermal conductivity coefficient was observed 0.14 W/mK in composites type A, consisting 25% fiber, 10% silica fume gel and 0.1% aluminium powder. In composites type A with increasing the aluminium powder to 0.1%, silica fume gel to 10% and fiber to 25%, the thermal conductivity reduced 36, 34.78 and 42.86 % respectively. Least thermal conductivity coefficient was measured 0.17 W/mK in type B composites containing 25% fiber, 10% silica fume gel and 30% fly ash. In composites type B with increasing the amount of fly ash to 30%, silica fume gel to 10% and fiber to 25%, the thermal conductivity did decease in order of 39.18, 37.5 and 47.62%. }, keywords = {: Fiber cement composite,Silica fume gel,Aluminium powder,Equisetum telmateia,Fly ash,Thermal conductivity}, title_fa = {بررسی تاثیر مواد افزودنی بر هدایت گرمایی چندسازه سیمان- الیاف گیاهی}, abstract_fa = {در این پژوهش چندسازه‌های الیاف – سیمان نوع A و B با هدایت گرمایی کم تولید شد. چند‌سازه‌ها‌ی نوع B از 15 و 25 درصد الیاف گیاه دم‌اسبی (Equisetum telmateia)، صفر، 7 و 10 درصد ژل میکروسیلیس و صفر، 20 و 30 درصد خاکستر سبک، ساخته شدند. در چندسازه‌های نوع A به جای خاکستر سبک، صفر، 08/0 و 1/0 درصد میکرو پودر آلومینیوم (همه بر پایه جرم خشک سیمان)، برای تولید چندسازه‌هایی با چگالی و ضخامت  اسمی g/cm³ 1/1 و mm 13 مورد استفاده قرار گرفت. نتایج به دست آمده از بررسی تاثیر این مواد بر هدایت گرمایی چند سازه‌های یاد شده نشان داد که افزایش میزان هر کدام از آن‌ها اثر معنی‌داری بر کاهش هدایت گرمایی چندسازه‌های تولید شده داشته است. کم‌ترین ضریب هدایت گرمایی در چندسازه‌ها‌ی A مربوط به چندسازه‌ی ساخته شده از 25 درصد الیاف، 10 درصد ژل میکروسیلیس و 1/0 درصد پودر آلومینیوم بود که برابر W/mK 14/0 تعیین شد. در چندسازه‌های نوع A‌ با افزایش پودر آلومینیوم تا 1/0 درصد، ژل میکروسیلیس تا 10 درصد و 25- 15درصد الیاف، هدایت گرمایی به ترتیب در حدود 36، 78/34 و 86/42 درصد کاهش یافت. کمترین ضریب هدایت گرمایی در مورد چندسازه‌های نوع B معادل W/mK 17/0 و مربوط به چندسازه‌ی دارای 25 درصد الیاف، 10 درصد ژل میکروسیلیس و 30 درصد خاکستر سبک تعیین شد. در چندسازه‌های نوع B با افزایش خاکستر سبک  تا 30 درصد، ژل میکروسیلیس تا 10 درصد و 25- 15 درصد الیاف، هدایت گرمایی به ترتیب در حدود 18/39، 5/37 و 62/47 درصد کاهش نشان داد.}, keywords_fa = {چندسازه الیاف سیمان,ژل میکروسیلیس,پودر آلومینیوم,گیاه دم اسبی,خاکستر سبک,هدایت گرمایی}, url = {https://www.ijwp.ir/article_11476.html}, eprint = {https://www.ijwp.ir/article_11476_023455374d90b3b8693867e57ece66dd.pdf} }