@article { author = {rastegarfar, nahid and behrooz, rabi and barikani, mehdi}, title = {Preparation of bio-polyols from lignocellulosic waste by liquefaction}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {313-321}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Rigid polyurethane foam (PUF) with desirable properties such as low thermal conductivity, easy production and processing is extensively used in the industrial applications. Currently, the PU industry is heavily petroleum-dependent, because its two major feedstocks, i.e. polyols and isocyanates, are largely petroleum-derived. Due to concerns over the depletion of fossil resources, pollution, there has been a great deal of interest in developing bio-based polyols from renewable resources. Lignocellulosic biomass is considered to be suitable for production of bio-based polyols, having hydroxyl group rich compounds. In bio-refining processes, the lignocellulosic macromolecular are broken down and converted into a viscous liquid using certain solvents. The use of high volumes of liquefaction solvents increases the production cost of bio-polyols. This has led to research on low cost and renewable solvents such as crude glycerol. In this research crude glycerol was used as solvent for liquefaction of sawdust and polyol production. The influence of process variables such as reaction temperature and time on polyol properties, namely biomass conversion ratio, acid number, hydroxyl number and viscosity were measured according to the certain standards. With increasing liquefaction temperature, increased production efficiency and viscosity and acid, hydroxyl number of polyols decreased. Finally, polyol of liquefaction at 180 and 360 min with production efficiency of 51%, acid, hydroxyl number and viscosity of 9/7, 325 mgKOH/g and 18 Pa,s was determinate as optimum polyol.}, keywords = {Liquefaction,Crude glycerol,Sawdust,Polyol,Polyurethane}, title_fa = {تهیه پلی ال زیستی از پسماند لیگنوسلولزی به روش مایع سازی}, abstract_fa = {فوم سخت پلی‌یورتان به‌دلیل دارا بودن ویژگی‌های مطلوبی مانند هدایت حرارتی کم و فرآیند تولید آسان، امروزه به‌طور گسترده‌ای استفاده می‌شود. در حال حاضر صنعت پلی‌یورتان به‌علت دو ماده اولیه عمده یعنی پلی‌ال‌ها و ایزوسیانات‌ها که از مشتقات نفتی می‌باشند، به‌طور زیادی به منابع پترو‌شیمیایی وابسته است. نگرانی کاهش منابع فسیلی و آلودگی موجب علاقه زیادی به توسعه پلی‌ال‌ها‌ی زیستی از منابع تجدید شونده شده است. مواد لیگنو‌سلولزی با داشتن ترکیباتی غنی از گروه‌های هیدروکسیل برای تولید پلی‌ال‌های زیستی مناسب می‌باشند. در فرآیند‌های پالایش زیستی با استفاده از حلال‌های معینی تا حد زیادی درشت مولکول-های ماده لیگنو‌سلولزی شکسته شده و به مایعی ویسکوز تبدیل می‌گردد. مصرف زیاد این حلال‌ها، افزایش هزینه تولید پلی‌ال‌ها را به‌دنبال داشته است. این امر سبب تحقیق بر روی حلال‌ها‌ی تجدید‌پذیر و ارزان‌قیمت مانند گلیسرول خام شده است. در این پژوهش از گلیسرول خام به عنوان حلال زیستی برای مایع سازی خاک اره و تولید پلی ال استفاده گردید. اثر عوامل فرآیندی زمان و دمای واکنش بر ویژگی‌ها‌ی پلی‌ال‌های حاصل بررسی شد. با افزایش دمای مایع سازی، عدد اسیدی و هیدروکسیل کاهش و بازده تولید و ویسکوزیته پلی ال-ها افزایش یافت. با بررسی دما‌ها و زمان‌های مختلف، پلی ال حاصل از مایع سازی در دمای 0C 180 به مدت 360 دقیقه، با بازدهی 51 درصد و عدد اسیدی و هیدوکسیل به ترتیب 7/9 و mgKOH/g 325 و ویسکوزیته Pa.s 16 به عنوان پلی ال بهینه تعیین گردید.}, keywords_fa = {مایع سازی,گلیسرول خام,خاک اره,پلی ال,پلی یورتان}, url = {https://www.ijwp.ir/article_28809.html}, eprint = {https://www.ijwp.ir/article_28809_8ff81a2382b53193dcc446d359995bf3.pdf} } @article { author = {Salari, Ayoub and faezipour, mahdi and karimi, alinaghi and jonoobi, mahdi and moradpour, payam}, title = {Investigation of the effect of modified poly vinyl acetate on the stress carrying capacity of corner joints in the wood members joined with dowel}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {323-336}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {AbstractThe aim of this study was to determine stress carrying capacity of doweled corner joints in wood members made with modified resin (polyvinyl acetate) and its comparison with unmodified ones. Joint members were out of European silver Fir (Abies alba) and dowels were made from Beech and poplar woods as variables in this study. Diameter of dowel had three levels in size, namely 6, 8 and 10 mm. The experimental joints were tested under diagonal compression loads. Results have shown that stress carrying capacity of tested joints made with modified glue is more than unmodified ones. Maximum stress capacity was observed in the joints of beech which with 10 mm in diameter dowels. Based on the results, the highest strength was belonging to those joints made with beech wood glued with modified resin containing 10 mm dowel. Furthermore, the lowest strength was belonging to poplar joints made with unmodified resins and 6 mm dowels. The improvement can be due to increased viscosity and controlled penetration of the resin into the wood structure and hence better bonding. Concerning the wood species, beech had the highest stress carrying capacity that it can attributed to its higher density. Key words: Stress carrying capacity, wooden dowel, modified PVAc, dowel.}, keywords = {Stress carrying capacity," wooden dowel," modified PVAc,dowel."}, title_fa = {ارزیابی تاثیر اصلاح چسب پلی وینیل استات بر ظرفیت لنگر خمشی اتصال‌ ساخته شده با پین چوبی}, abstract_fa = {چکیده هدف از این پژوهش بررسی تاثیر چسب اصلاح شده‌ی پلی وینیل استات بر ظرفیت لنگر خمشی اتصال‌های ساخته شده از گونه‌های راش صنوبر و نراد بوده است. در این پژوهش ظرفیت لنگر خمشی اتصال‌ با چسب اصلاح شده مورد بررسی قرار گرفته و با چسب اصلاح نشده مقایسه شده است. مواد مورد استفاده در این تحقیق چسب پلی وینیل استات و گونه‌های چوبی راش، صنوبر و نراد بوده است. نتایج نشان داد که بیشترین ظرفیت لنگر خمشی 1/47 نیوتن متر مربوط به اتصال راش با قطر پین 10 میلیمتر و چسب اصلاح شده بوده در حالی که کمترین لنگر خمشی 17/35 نیوتن متر مربوط به اتصال با گونه صنوبر با قطر 6 برای چسب اصلاح نشده بود. اصلاح چسب پلی وینیل استات با نانو سلولز و پلی وینیل الکل تاثیر مطلوبی روی خواص مکانیکی این چسب داشته که اختلاف مقاومت اتصال چسب اصلاح شده با پلی وینیل استات خالص گواه این مطلب است که علت ان می تواند افزایش ویسکوزیته چسب و کنترل میزان نفوذ آن به بافت چوب و بهبود چسبندگی باشد. از بین قطر پین های مورد مطالعه، قطر 10 میلیمتر به واسطه محیط بیشتر و به طبع آن مساحت سطح چسبندگی بیشتر، استحکام بالاتری نسبت به قطرهای 8 و 6 میلیمتر نشان داد. همانطور که قابل پیش بینی بود مقاومت اتصال گونه راش بالاتر از نراد و صنوبر بود، که دلیل اصلی آن را می توان به دانسیته بالاتر این گونه ربط داد.کلمات کلیدیچسب پلی‌وینیل‌استات اصلاح شده، اتصال دوبل با پین چوبی، ظرفیت لنگر خمشی، نانو کریستال سلولز}, keywords_fa = {"چسب پلی‌وینیل‌استات اصلاح شده," اتصال دوبل با پین چوبی,ظرفیت لنگر خمشی," نانو کریستال سلولز"}, url = {https://www.ijwp.ir/article_29992.html}, eprint = {https://www.ijwp.ir/article_29992_e3f80037ade017429f44a1cd99aa3c67.pdf} } @article { author = {Karimi, Abdollah and jamalirad, loya and Aminian, Hedayatollah and Hedjazi, Sahab}, title = {The effect of using Alkali sulfit-Anthraquinone (AS-AQ) liquor powder as filler of urea formaldehyde resin on functional properties of plywood}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {337-347}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this research, the use of alkali sulfite - anthraquinone liqueur powder as filler of urea formaldehyde resin and replacing with wheat flour in the production of plywood was considered. The AS-AQ liquor powder was used as filler of UF resin in plywood manufacture at four levels of 0, 5, 10 and 15% based on oven dry weight of UF resin. Then the physical and mechanical properties of the samples, including thickness swelling after 2 and 24 hours immersion in water, bending strength and modulus of elasticity (parallel and perpendicular to surface grain) and bonding shear strength were measured. The results showed that the amount of thickness swelling of the boards after 2 and 24 hours of immersion in water did not increase significantly, and all the levels had a thickness swelling at the standard level. Increasing the consumption of liqueur powder did not have a negative significant effect on the dimensional stability of the boards. Bending strength and modulus of elasticity parallel and perpendicular to the surface layer fiber was improved by an increase in the use of liquor powder, but there was no significant difference between the difference levels. Therefore considering the physical and mechanical properties of the boards, it is appropriate to use alkali sulfite - anthraquinone (AS-AQ) liqueur powder as filler of urea formaldehyde resin.}, keywords = {black liquor,Alkali sulfite – anthraquinone process,Urea formaldehyde resin,Filler,Plywood}, title_fa = {تأثیر استفاده از پودر مایع سیاه پخت سولفیت قلیایی - آنتراکینون به عنوان پرکننده رزین اوره فرمالدهید بر ویژگی های کاربردی تخته لایه}, abstract_fa = {در این تحقیق استفاده از پودر مایع سیاه پخت فرآیند تولید خمیرکاغذ به عنوان پرکننده رزین اوره فرمالدهید و جایگزین آرد گندم در ساخت تخته‌لایه مورد بررسی قرار گرفت. از پودر مایع سیاه پخت سولفیت قلیایی- آنتراکینون در چهار سطح ۰، ۵، ۱۰ و ۱۵ درصد وزن خشک رزین به عنوان پرکننده چسب برای ساخت تخته‌لایه صنوبر استفاده شد. سپس خواص فیزیکی و مکانیکی نمونه‌های آزمونی شامل واکشیدگی ضخامت بعد از ۲ و ۲۴ ساعت غوطه‌وری در آب، مقاومت خمشی، مدول الاستیسیته موازی و عمود بر الیاف لایه سطحی و مقاومت برشی اندازه‌گیری شد. نتایج نشان داد که مقدار واکشیدگی ضخامت تخته‌ها بعد از ۲ و ۲۴ ساعت غوطه‌وری در آب افزایش معنی‌داری ندارد و همه سطوح دارای واکشیدگی ضخامت استاندارد بود. افزایش مصرف پودر مایع سیاه پخت تأثیر منفی معنی-داری بر پایداری ابعادی تخته‌ها نداشت. مقاومت خمشی، مقاومت برشی و مدول الاستیسیته موازی و عمود با الیاف لایه سطحی با افزایش استفاده از پودر مایع سیاه پخت بهبود یافت اما اختلاف معنی‌داری بین سطوح مختلف دیده نشد. با توجه به خواص فیزیکی و مکانیکی، می‌توان استفاده از پودر مایع سیاه پخت حاصل از فرآیند پخت سولفیت قلیایی- آنتراکینون را به عنوان پرکننده چسب اوره فرمالدهید توصیه نمود.}, keywords_fa = {مایع سیاه پخت صنایع خمیر و کاغذ,فرآیند سولفیت قلیایی-آنتراکینون,رزین اوره فرمالدهید,پرکننده,تخته‌لایه}, url = {https://www.ijwp.ir/article_33266.html}, eprint = {https://www.ijwp.ir/article_33266_d2fab54826360016a564a1db589ce3bf.pdf} } @article { author = {hejazi, sahab and Hajipour, Hedieh and Abdolkhani, Ali and hamzeh, yahya and jamalirad, loya}, title = {Comparing lignin derived from black liquors of alkaline sulfite-AQ, soda-AQ and kraft processes as a filler-extender in the poplar plywood}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {349-358}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {According to the importance of urea formaldehyde resin in plywood industry and to replace a suitable filler for this resin with wheat flour (common filler), lignin drived from three black liquors including alkaline sulfite-AQ, soda-AQ and Kraft evaluated as filler-extender for urea formaldehyde resin in the plywood manufacture. For this reason any of the four types of lignins were used at 0, 10, 20 and 30% dry weight of resin.After that, the physical and mechanical properties of samples including thickness swelling after 2 and 24 hours immersion in water, flexural strength and modulus of elasticity parallel and perpendicular to fiber the surface layer and shear strength were measured.The results of this study showed that increasing thelignin of alkali sulfite-anthraquinone and then kraft lignin, flexural strength and modulus of elasticity parallel to the fiber surface layer increased.Also, the bonding shear strength of the samples using three types of lignins increased. On the other hand, the use of these three types of lignin, improved the dimensional stability of the boards.The results show the superiority of lignin from alkaline sulfite anthraquinone process compared to other lignins to improving the mechanical properties of plywood.}, keywords = {Lignin,alkali sulfite-AQ,soda-AQ,Kraft,Filler-Extender}, title_fa = {مقایسه لیگنین حاصل از مایع پخت سیاه فرآیندهای سولفیت قلیایی – آنتراکینون، سودا-آنتراکینون و کرافت به عنوان فیلر-اکستندردر ساخت تخته لایه صنوبر}, abstract_fa = {با توجه به اهمیت پرکننده رزین اوره فرمالدهید در صنعت تخته‌لایه و با هدف جایگزینی یک پرکننده مناسب برای این نوع چسب با آرد گندم (پرکننده متداول)، لیگنین حاصل از سه مایع پخت سیاه فرآیندهای سولفیت قلیایی-آنتراکینون، سودا-آنتراکینون و کرافت به عنوان فیلر-اکستندر رزین اوره فرمالدهید در ساخت تخته‌لایه مورد بررسی قرار گرفت. برای این منظور از هر یک از انواع لیگنین‌ها، در چهار سطح 0، 10، 20 و 30 درصد بر اساس وزن خشک رزین استفاده شد. سپس خواص فیزیکی و مکانیکی نمونه‌های آزمونی شامل واکشیدگی ضخامت بعد از 2 و 24 ساعت غوطه‌وری در آب، مقاومت خمشی و مدول الاستیسیته موازی و عمود بر الیاف لایه سطحی و مقاومت برشی اندازه‌گیری شد. نتایج حاصل از این بررسی نشان دادند که به ترتیب با افزایش مصرف لیگنین سولفیت قلیایی-آنتراکینون و لیگنین کرافت، مقاومت خمشی و مدول الاستیسیته موازی با الیاف لایه سطحی افزایش یافت. همچنین مقاومت برشی در سطح اتصال نمونه‌ها در صورت استفاده از هر سه نوع لیگنین نیز افزایش نشان داد. از سوی دیگر استفاده از این سه نوع لیگنین، باعث بهبود پایداری ابعادی تخته‌ها شد. نتایج حاکی از برتری لیگنین حاصل از فرآیند سولفیت قلیائی- آنتراکینون در مقایسه با سایر لیگنین‌ها در بهبود ویژگی‌های مکانیکی تخته لایه می باشد.}, keywords_fa = {لیگنین,سولفیت قلیایی-آنتراکینون,سودا-آنتراکینون,کرافت,فیلر- اکستندر}, url = {https://www.ijwp.ir/article_31253.html}, eprint = {https://www.ijwp.ir/article_31253_ea6f54adcf3eab0b10358c6b50ebe5e6.pdf} } @article { author = {rudi, hamidreza and Atun, Davod and Jalali Torshizi, Hosein and Djafari Petroudy, Seyed Rahman}, title = {Effect of Applying Cellulose Nanofibers on the Properties of Multiply Paper Made from Recycled Fibers}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {359-369}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The use of cellulose nanofibers as strength-enhancing additive in the wet end section of paper machine increases the general strengths of paper. Nevertheless, considerable increase in draining time from pulp suspension and decrease in paper porosity and opacity has been reported as substantial restriction of its application in this section of papermaking. In this study, the effect of applying cellulose nanofibers in the forming section of paper on the properties of three-ply paper made from recycled fibers has been examined. Samples of recycled fibers has been prepared from Atrak pulp and paper industries. To do, the refined and not dispersed pulp were respectively used to form top layer and other two layer. Standard sheets with 40±2 g/m2 basis weight were prepared from each of recycled pulps. Then, cellulose nanofibers spray in 1, 2, 4 and 6 levels (based on oven dry fibers) on one sheet surface and subsequently mild suction was done applying cellulose nanofibers spraying machine which designed and fabricated in Zirab research campus. Finally, three-ply paper with 120±5 g/m2 basis weight were prepared using treated sheets and its properties were evaluated. The overall results revealed that spraying cellulose nanofibers on the forming sheet has led to increase in tensile and burst indices of the paper about 33.59 and 26.29 percent respectively. This process particularly had a considerable effect on the strength improvement between layers in multi-ply paper which is most important in these kind of papers. Thereby, the value of this strength has been significantly increased from roughly 116 J/m2 to 217 J/m2. SEM micrographs prepared from paper thickness confirm larger link between layers and multi-ply condensation.}, keywords = {Recycled Fibers,Multiply Paper,Cellulose Nanofibers,Forming,Plybond}, title_fa = {تأثیر بکارگیری نانوالیاف سلولزی بر ویژگی‌های کاغذ چندلایه تهیه شده از الیاف بازیافتی}, abstract_fa = {استفاده از نانوالیاف سلولزی به‌عنوان افزودنی مقاومت‌دهنده در بخش پایانه تر ماشین کاغذ مقاومت‌های کلی کاغذ را افزایش می‌دهد. امّا افزایش قابل ملاحظه زمان آبگیری از سوسپانسیون خمیرکاغذ و کاهش تخلخل و ماتی کاغذ از جمله محدودیت‌های اساسی بکارگیری از آن در این بخش کاغذسازی گزارش شده است. در این پژوهش، تأثیر استفاده از نانوالیاف سلولزی در بخش شکل‌گیری کاغذ بر روی ویژگی‌های کاغذ سه‌لایه تهیه شده از الیاف بازیافتی مورد بررسی قرار گرفت. نمونه های الیاف بازیافتی از صنایع خمیر و کاغذ اترک تهیه شد. بدین منظور خمیرکاغذ پالایش شده و پراکنده نشده بترتیب برای تهیه کاغذ لایه رویی و دو لایه دیگر استفاده شدند. از هر یک از خمیرکاغذهای بازیافتی کاغذهای دست ساز استاندارد با گراماژ 2±40 گرم بر مترمربع تهیه شد. سپس پاشش نانوالیاف سلولز در چهار سطح 1، 2، 4 و 6 درصد (براساس وزن خشک الیاف) بر روی یک سطح ورقه تر و متعاقباً مکش ملایم آن با استفاده از دستگاه پاشش نانوالیاف سلولز که در پردیس علمی تحقیقاتی زیراب طراحی و ساخته شد، انجام گرفت. با استفاده از کاغذهای تیمارشده، کاغذ سه‌لایه با گراماژ حدود 5±120 گرم بر مترمربع تهیه و ویژگی‌های آن موردارزیابی قرار گرفت. نتایج کلی نشان داد که پاشش نانوالیاف سلولز بر روی ورقه در حال شکل‌گیری، بترتیب باعث افزایش شاخص‌های کششی و ترکیدن کاغذ بمیزان 59/33 و 29/26 درصد شده است. این فرآیند بویژه تأثیر قابل ملاحظه‌ای در بهبود مقاومت بین لایه‌های کاغذ چندلایه دارد که در این نوع کاغذها بسیار مهم است. بطوری‌که مقدار این مقاومت از حدود J/m2 116 به J/m2 217 افزایش معنی‌داری یافته است. تصاویر SEM تهیه‌شده از ضخامت کاغذ، اتصال بیشتر بین لایه‌ها و فشردگی کاغذ چندلایه را تأیید می‌کند.}, keywords_fa = {الیاف بازیافتی,کاغذ چندلا,نانوالیاف سلولز,شکل‌گیری,مقاومت بین لایه‌ها}, url = {https://www.ijwp.ir/article_30147.html}, eprint = {https://www.ijwp.ir/article_30147_39331269c82189cdee07ccda602a4880.pdf} } @article { author = {dadmohamadi, kobra and azadi, mehrnaz and abed esfahani, abbas}, title = {evaluation function rice starch glues of rehabilitation and activation in preparation Tissues used in restoration paper works}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {371-382}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The aim of this research were to facilitate the use of starch in paper works that combined they are not sensitive to water and also identify the characteristics of adhesives (sheets) enabled starch and starch together new. The research, analytical comparison And gathering data through experiments related to research Like pH measurement, colorimetric, infrared spectroscopy with attenuated total reflection (FTIR- ATR), Measurement of tensile strength and adhesion strength of the samples was also measured. The present study was thus that the adhesives were prepared rice starch and rice starch plate enabled. The Prototyping was done using adhesives. Temperature-humidity accelerated aging specimens in accordance with ASTM D7414-96 number for 384 hours and changes color, pH, tensile strength and adhesion are studied. The results showed The highest acidity after two rounds of the sample aging RS (tissue paper coated with glue rice starch) with pH 6/1 after the aging light And 6/01 after temperature-humidity aging And the lowest acidity of the average of the samples SF (plate starch) with pH 8/35 After light aging and pH 8/20 after temperature-humidity. After Light and temperature-humidity aging, the highest tensile strength of the sample RS is the 1/08 kN per meter. Reviews results that the adhesion strength test showed after stage aging light, The maximum adhesion of the sample RS 1/32 Newton and after the temperature-humidity aging of the highest adhesion of ASF to value 1/25 Newton.}, keywords = {rice starch glue,activation,rehabilitation,tissue,restoration of paper works}, title_fa = {ارزیابی عملکرد چسب نشاسته برنج بازپروری و فعال‌سازی شده در آماده‌سازی تیشوهای مورداستفاده در مرمت آثار کاغذی}, abstract_fa = {هدف از انجام این تحقیق تسهیل به‌کارگیری چسب نشاسته در مرمت آثار کاغذی که مرکب آن‌ها نسبت به آب حساس نیست و همچنین شناسایی ویژگی‌های چسب (ورق) نشاسته فعال‌شده و چسب نشاسته تازه با یکدیگر است. روش انجام پژوهش، تحلیلی- مقایسه‌ای و شیوه گردآوری داده‌ها از طریق آزمایش‌های مرتبط با موضوع پژوهش همچون pH سنجی، رنگ سنجی، طیف‌سنجی مادون‌قرمز با بازتاب کلی تضعیف‌شده (FTIR- ATR)، اندازه‌گیری مقاومت کششی و همچنین اندازه‌گیری مقاومت چسبندگی نمونه‌ها بوده است. مراحل انجام پژوهش حاضر بدین گونه بود که ابتدا چسب نشاسته برنج و ورق فعال‌شده نشاسته برنج آماده شد. سپس با استفاده از این چسب‌ها نمونه‌سازی‌ها انجام شد. نمونه‌های آماده‌شده تحت پیرسازی تسریعی دما- رطوبت طبق استاندارد ASTM به شماره D7414-96 به مدت 384 ساعت و نور طبق استاندارد ASTM به شماره D6789-02 به مدت 360 ساعت قرار گرفتند و تغییرات رنگ،pH، مقاومت کششی و میزان چسبندگی آن‌ها، موردبررسی قرار گرفت. نتایج نشان داد، بالاترین میزان اسیدیته پس از دو مرحله پیرسازی مربوط به نمونه RS (کاغذ تیشوی آغشته به چسب نشاسته برنج) با pH 1/6 پس از پیرسازی نوری و 01/6 پس از پیرسازی دما- رطوبت می‌باشد و پایین‌ترین میزان اسیدیته نیز به‌طور میانگین مربوط به نمونه‌های SF (ورق نشاسته) با pH 35/8 پس از پیرسازی نوری و pH 20/8 پس از پیرسازی دما- رطوبت می‌باشد. پس از پیرسازی نوری و دما- رطوبت، بیشترین میزان مقاومت کششی مربوط به نمونه RS به میزان 08/1 کیلو نیوتن بر متر است. بررسی نتایج حاصل از آزمون مقاومت چسبندگی نیز نشان داد که پس از مرحله پیرسازی نوری، بیشترین میزان چسبندگی مربوط به نمونه RS به میزان 32/1 نیوتن و پس از پیرسازی دما- رطوبت نیز بیشترین میزان چسبندگی مربوط به نمونه ASF به مقدار 25/1 نیوتن است.}, keywords_fa = {چسب نشاسته برنج,فعال‌سازی,بازپروری,تیشو,مرمت آثار کاغذی}, url = {https://www.ijwp.ir/article_30194.html}, eprint = {https://www.ijwp.ir/article_30194_358e266966bfe9a146b91a6c397f20bb.pdf} } @article { author = {Jafarnezhad, Saber and Shalbafan, Ali and Luedtke, Jan}, title = {Effect of the Expanded Polystyrene Granules on the Physical and Mechanical Properties of Hybrid Lightweight Panels}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {383-396}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The aim of the present study is the production of low density hybrid panels using expanded polystyrene granules (EPS) with different diameter and percentage. Expanded polystyrene granules used in 3 forms of fine, medium and large granules with an average diameters of 0.55, 2 and 7 mm, respectively. The amount of EPS substituted in the core layer was 5, 10 and 15% based on oven dry mass of wood coarse particles. The results showed that the mechanical properties (modulus of elasticity, internal bond, face and edge screw withdrawal resistance) were significantly enhanced with increasing the EPS diameters. Increasing the amount of EPS from 5 to 15% had also shown that the internal bond and physical properties were significantly improved. The bending properties and screw withdrawal resistance (both face and edge) were not significantly influenced with increasing the EPS content. The most important findings from these research was that the improvement of all properties were observed with using polystyrene granules in core layer in comparison with reference panels.}, keywords = {Hybrid panel,lightweight,polystyrene granule,expanded}, title_fa = {تاثیر گرانول‌های پلی‌استایرن منبسط شده بر ویژگی‌های فیزیکی و مکانیکی پانل‌های سبک وزن ترکیبی}, abstract_fa = {هدف از تحقیق حاضر تولید تخته‌های سبک وزن ترکیبی با استفاده از گرانول‌های پلی‌استایرن منبسط شده با قطر و درصدهای مختلف بوده است. گرانول‌های پلی‌استایرن منبسط شده در 3 قطر ریز، متوسط و درشت به ترتیب با میانگین قطرهای 55/0، 2 و 7 میلیمتر و به میزان 10 درصد وزن خشک خرده‌چوب-های لایه مرکزی استفاده گردید. همچنین از گرانول‌های با میانگین قطر 7 میلیمتر در 3 سطح 5، 10 و 15 درصد وزن خشک خرده‌چوب‌های لایه مرکزی استفاده گردید. نتایج نشان دادند که ویژگی‌های مکانیکی (مدول الاستیسیته خمشی، چسبندگی داخلی، مقاومت به پیج سطح و لبه) با افزایش قطر گرانول‌ها افزایش قابل توجهی یافته است، اما قطر گرانول‌ها تاثیر معنی‌داری بر مقاومت خمشی، درصد واکشیدگی ضخامت و جذب آب نمونه‌ها نداشته است. همچنین افزایش درصد گرانول‌های پلی‌استایرنی در لایه میانی باعث افزایش ویژگی‌های مکانیکی و بهبود خصوصیات فیزیکی نسبت به نمونه شاهد گردید و بیشترین اثر گذاری آن بر چسبندگی داخلی نمونه‌ها مشاهده شد.}, keywords_fa = {پانل ترکیبی,سبک‌وزن,گرانول پلی‌استایرن,منبسط شده}, url = {https://www.ijwp.ir/article_30345.html}, eprint = {https://www.ijwp.ir/article_30345_b481891c64782a1d6304215841a0a657.pdf} } @article { author = {Rahimi, Atefe and Hamzeh, Yahya and Abdolkhani, Ali and Hedjazi, Sahab and Izadyar, soheila}, title = {The use of lignocellulosic waste of rice straw for AO7 and RBB dyes adsorption from water}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {397-409}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this research, rice straw was used as a low-cost and abundant lignocellulose material for adsorption of acidic and reactive dyes from aqueous solution and their adsorption efficiency has been investigated. Rice straw was used after grinding and extraction. The studied dyes were Orangan 7 (AO7) and Rimozol Black B (RBB) obtained from Alvand Sabet Co. in Hamadan. In this study, the effect of pH, temperature, adsorbent and dyes concentration, and adsorption time were investigated to determine the optimum adsorption conditions. Also the adsorption isotherm was studied for both dyes. The results of color adsorption by rice straw showed that the amount of adsorption depended largely on the pH of the solution, and in acidic pH the removal of the dye by rice straw was high. Also, the dye adsorption at the initial stages of treatment is very fast and more than 95% of the adsorption of dye takes place at the first 5 minutes. The adsorption rate was studied using well-known adsorption models, and the results indicated that the equilibrium data for both dyes were perfectly described by the Langmuir isotherm. The maximum adsorptions of rice straw were 16.5 mg/g and 27.3 mg/g for RBB and AO7, respectively. Due to low cost and abundance of rice straw, it could be a suitable material for removal of dyes pollutants from industrial and municipal wastewater.}, keywords = {rice straw,Absorption,Dyes,Adsorption isotherm}, title_fa = {کاربرد کلش برنج در جذب رنگ‌های اسید اورانژ و ریموزول بلک از پساب‌های شبیه-سازی شده صنایع نساجی}, abstract_fa = {در این تحقیق از کلش برنج که جزء مواد لیگنوسلولزی فراوان و ارزان‌ قیمت در کشور است برای جذب رنگ‌های اسیدی و واکنشی از آب استفاده ‌شد و کارایی جذب آن مورد بررسی قرار گرفت. کلش برنج به‌عنوان ماده اولیه از مزارع برنج شمال تهیه ‌شد و بعد از خردکردن و استخراج مواد استخراجی مورد استفاده قرار گرفت. رنگ‌های مورد استفاده شامل اسید اورانژ 7 (AO7) و ریموزول بلکB (RBB) از شرکت الوان ثابت همدان تهیه‌ شد. در این تحقیق اثر pHپساب، دما، مقدار جاذب، غلظت رنگ و زمان برای تعیین شرایط بهینه جذب بررسی شد و مدل‌های جذب ایزوترم برای هر دو رنگ مورد مطالعه قرار گرفت. نتایج حاصل از جذب رنگ توسط کلش برنج نشان داد که میزان جذب به مقدار زیادی بهpH محلول بستگی دارد و در pH های اسیدی کارایی حذف رنگ ساقه برنج در حد بالایی قرار دارد و با افزایش pH از 2تا 12میزان حذف رنگ تا 50% کاهش می‌یابد. همچنین میزان جذب رنگ در زمان‌های اولیه تیمار بسیار سریع است و حدود بیش از 95% جذب رنگ در 5 دقیقه اول رخ می‌دهد. میزان حداکثر جذب رنگ AO7 توسط کلش برنج برابر 3/27 میلی‌گرم بر گرم و برای رنگ RBB برابر 5/16 میلی‌گرم بر گرم تعیین شد و پیروی ایزوترم جذب هر دو رنگ از مدل لانگمویر مشاهده گردید. با توجه به نتایج، می‌توان گفت که کلش برنج به دلیل ارزان‌قیمت بودن و فراوانی گزینه مناسبی برای حذف آلاینده‌های رنگی از پساب‌های صنعتی و شهری می‌باشد.}, keywords_fa = {کلش برنج,جذب,رنگ,مدل‌های جذب,ایزوترم}, url = {https://www.ijwp.ir/article_30921.html}, eprint = {https://www.ijwp.ir/article_30921_2ca771e20d89ab6c16e879115cca05bc.pdf} } @article { author = {Efhamisisi, Davood and Hamzeh, Yahya}, title = {Borates and their applications to preserve wood-based composites}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {411-428}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Wood and any items made from the wood may be destroyed by biologic and abiotic factors in unsuitable conditions. So far, different materials and methods have been developed to improve disadvantages of wood. Nowadays researchers are looking for safe and eco-friendly preservatives due to the public concerns about negative impacts of old ones. Borates are good candidate for new generation of wood preservatives due to the low acute toxicity for mammalians. Borates have board-spectrum efficacy, they are not only fungicide and insecticide but also act as a fire retardant. They are easily dissolved in water and can be diffused deeper into the wood over the time. This is also their biggest disadvantage. Preservatives based on the borate formulations may be easily leached out from the treated wood in the outdoor applications. Today, despite the problems coming from their leaching, they are widely used to protect wood and in particular wood-based composites due to their low toxicity. This study attempts to review the latest research on the possibility of using borates as pesticides and fire retardant in the industry of wood-based composites. Borates have a great potential for protecting wooden composites which are currently commercially used.}, keywords = {Borates,wood-based composites,biological deterioration,fire,environment}, title_fa = {بورات ها و کاربرد آنها در حفاظت چندسازه‌های چوبی}, abstract_fa = {چوب و هر چیز ساخته شده از آن در شرایط نامناسب بر اثر عوامل مخرب زنده و غیرزنده تخریب می‌‌شود. تاکنون روش‌ها‌ و مواد مختلفی برای بهبود معایب چوب و چندسازه‌های چوبی توسعه یافته‌اند. اما امروزه به دلیل نگرانی‌های عمومی در مورد اثرات سوء مواد حفاظتی قدیمی محققین به دنبال مواد دوست‌دار محیط زیست و ایمن هستند. بورات‌‌‌ها به دلیل سمیت حاد کم نامزد مناسبی برای نسل جدید مواد حفاظتی می‌باشند. بورات‌ها دامنه اثرگذاری وسیعی دارند، نه‌ تنها قارچ کش و حشره‌کش موثری هستند بلکه به عنوان یک کندسوز کننده نیز عمل می‌کنند. بورات‌ها به آسانی در آب حل شده و قابلیت انتشار تا عمق چوب را دارند. همین مزیت بورات‌ها بزرگترین عیب آنها نیز برشمرده می‌شود. فرمولاسیون‌های بر پایه بورات به آسانی آبشویی شده و برای مصارف بیرونی مناسب نیستند. امروزه علی‌رغم مشکل آبشویی، از بورات‌ها به دلیل سمیت بسیار کم به طور وسیعی برای حفاظت چوب و به ویژه چندسازه‌های چوبی در برابر عوامل مخرب زنده و غیر زنده مانند آتش استفاده می‌شود. در این گزارش سعی شده است جدیدترین تحقیقات انجام شده بر روی امکان استفاده از بورات‌ها در صنعت چندسازه‌های چوبی مورد بازبینی قرار گیرد. ترکیبات مختلف بورات قابلیت زیادی برای حفاظت چندسازه‌های چوبی دارند و در حال حاضر به صورت تجاری از آنها استفاده می‌شود.}, keywords_fa = {بورات ها,چندسازه های چوبی,تخریب زیستی,آتش,محیط زیست}, url = {https://www.ijwp.ir/article_30998.html}, eprint = {https://www.ijwp.ir/article_30998_e928e7744cbe3589d37103dcc07bbe72.pdf} } @article { author = {Dastoorian, Foroogh}, title = {Determination of elastic modulus of a natural fiber- thermoplastic composite}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {429-440}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In the present study, three methods of compressive loading test, loading-unloading test and ultrasonic test were used to determine the elastic modulus of a natural fiber-thermoplastic composite. Results showed that the composite had orthotropic nature and the dynamic modulus from ultrasonic test showed higher values compared to the two others. Also with increasing modulus resulted from unloading test, the difference between dynamic and unloading modulus decreased linearly. Results also showed that using prevalent method of modulus determination for this material (i.e. tangent modulus at 10-40% of ultimate stress) leads to the elastic modulus estimated much lower than the real value.}, keywords = {elastic modulus,ultrasonic test,loading-unloading test}, title_fa = {تعیین مدول الاستیسیته ماده مرکب الیاف طبیعی-ترموپلاستیک}, abstract_fa = {در تحقیق حاضر از سه روش آزمون فشاری استاتیک، آزمون بارگذاری-حذف بار و فراصوت برای تعیین مدول الاستیسته ماده مرکب الیاف طبیعی- پلی‌پروپیلن ساخته شده به روش اکستروژن استفاده گردید. نتایج نشان داد که این ماده مرکب از ماهیت ارتوتروپیک برخوردار است و مدول دینامیک حاصل از آزمون فراصوت از مقدار بیشتری در مقایسه با دو مدول دیگر برخوردار است. همچنین با افزایش مدول حاصل از آزمون حذف بار، درصد اختلاف بین مدول حذف بار و مدول دینامیک کاهش یافت. نتایج همچنین نشان داد که استفاده از روش رایج تعیین مدول (مدول تانژانت در 10 تا 40 درصد تنش نهایی) برای این ماده، سبب می‌شود مقدار مدول بسیار کمتر از مقدار واقعی برآورد گردد.}, keywords_fa = {مدول الاستیسیته,آزمون فراصوت,آزمون بارگذاری- حذف بار}, url = {https://www.ijwp.ir/article_31119.html}, eprint = {https://www.ijwp.ir/article_31119_41b8dd2b464776013a0f67862ba15d3d.pdf} } @article { author = {ghahramani, negin and ramezani, omid and kermanian, hossein and vatankhah, elham and kousha, mojtaba}, title = {Acidic prehydrolysis role in dissolving pulp production from OCC}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {441-457}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Acid prehydrolysis aiming to remove hemicelluloses is one the key steps in producing dissolving pulp from wood resources. The objective of the present research is to resolve the necessity of using tis treatment in dissolving pulp production from old corrugated container. Therefore, temperature of 130 C, acid concentration of 1%, time of 30 min and liquor to paper of 7:1 were selected as acid pretreatment and the properties of both samples of with and without prehydrolysis were compared after cooking. The results showed that excluding reactivity, other dissolving pulp required properties including accessibility, degree of polymerization and the alpha cellulose content were diminished. Also, the results of yield and chemical composition indicated the destruction of this step to samples. Finally, regarding the superior properties of samples with no prehydrolysis and their acceptable value of reactivity, not only the acid prehydrolysis necessity was not acknowledged but also its application is not recommended.}, keywords = {Dissolving pulp,old corrugated container,Acid Prehydrolysius,Reactivity,Accessibility}, title_fa = {نقش پیش هیدرولیزاسیدی در تولید خمیر حل‌شونده از مقوای کنگره‌ای کهنه}, abstract_fa = {عملیات پیش‌هیرولیز اسیدی با هدف حذف همی‌سلولزها یکی از مراحل اصلی در تولید خمیرهای حل‌شونده از منابع چوبی است. تحقیق حاضر به بررسی ضرورت اعمال این تیمار در تولید خمیرحل‌شونده از مقوای کنگره‌ای کهنه می‌پردازد. بدین منظور ابتدا شرایط دمای 130 درجه سانتی‌گراد، غلظت اسید 1 درصد، زمان 30 دقیقه و نسبت لیکور به کاغذباطله 7:1 بعنوان پیش‌تیمار اسیدی برگزیده شد و در ادامه ویژگی‌های کیفی دو نمونه دارای پیش‌هیدرولیز و فاقد پیش‌هیدرولیز پس از پخت با یکدیگر مقایسه شد. نتایج نشان داد که به استثنای شاخص واکنش‌پذیری، سایر ویژگی‌های مورد نیاز خمیر‌حل‌شونده مانند دسترسی-پذیری، درجه بسپارش و میزان سلولز آلفا در اثر اعمال پیش‌تیمار اسیدی دچار نقصان می‌شوند. نتایج مربوط به اندازه‌گیری بازده و ترکیبات شیمیایی نیز حاکی از آسیب رساندن این مرحله به نمونه‌ها بود. در نهایت، با در نظر گرفتن اهمیت شاخصه‌های کیفی برتر خمیرهای فاقد پیش‌هیدولیز اسیدی و نیز قابل قبول بودن مقدار واکنش‌‌پذیری این نمونه‌ها، نه تنها ضرورت اعمال تیمار مذکور شناخته نشد بلکه توصیه به عدم استفاده از آن بود.}, keywords_fa = {خمیر حل شونده,مقوای کنگره ای کهنه,پیش هیدرولیز اسیدی,واکنش پذیری,دسترسی پذیری}, url = {https://www.ijwp.ir/article_31193.html}, eprint = {https://www.ijwp.ir/article_31193_e49503a6c0560507614ee0362bdf643e.pdf} } @article { author = {Amiri, Elmira and Rahmaninia, Mehdi and Khosravani, Amir}, title = {Effect of Chitosan Electrostatic Charge on the Performance of Chitosan-Nanosilica in Recycled Old Corrugated Container Pulp}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {9}, number = {3}, pages = {459-469}, year = {2018}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Using chitosan-nanosilica system in papermaking has been considered in researches recently. In present investigation, confirming the performance of this nanoparticle system in producing paperboard from recycled old corrugated container pulp, the electrostatic performance of chitosan polyelectrolyte in process and product properties has been considered. In this respect, pH of pulp suspension, as one of mains factor affecting the chitosan electrostatic charge, was considered. The results indicated that the process properties (drainage and first pass retention) have been experienced better situation affected by chitosan electrostatic charge in neutral and alkaline conditions. It seems that by changing the pulp suspension pH to neutral and alkaline conditions, the chitosan positive electrostatic charge and its solubility would be decreased and in contrast the fibers negative charge would be increased. This condition would probably affect the chitosan polymer connection and deployment status on fibers surface (loop and tail position) which might perform more effective in floc formation and therefore, drainage and retention increment about 37.5 and 36.5% respectively comparing with control sample and 34 and 7% respectively in comparison with acidic condition. Although the mentioned system has been successful in increasing the mechanical strength comparing the control samples, but the electrostatic charge changes in different pH conditions had less positive impact on these properties (except internal bonding strength).}, keywords = {Chitosan,Electrostatic Charge,Process and Mechanical properties,Nanosilica,Recycled Fibers}, title_fa = {تاثیر بار الکتروستاتیکی کایتوزان بر عملکرد سیستم کایتوزان- نانو سیلیکا در خمیرکاغذ بازیافتی کارتن‌های کنگره‌ای کهنه}, abstract_fa = {اخیرا استفاده از سیستم کایتوزان-نانوسیلیکا در کاغذسازی، در تحقیقات مورد توجه قرار گرفته است. در این راستا پژوهش حاضر با تایید نتایج عملکرد این سیستم نانوذره در فرآیند تولید مقوا از خمیرکاغذ بازیافتی کارتن های کنگره ای کهنه، به بررسی عملکرد الکتروستاتیکی پلی الکترولیت کایتوزان در ویژگی های مربوط به فرآیند تولید و کیفیت محصول تولیدی پرداخته است. بر این اساس تغییر pH خمیرکاغذ به عنوان یکی از اصلی ترین عوامل موثر بر بار الکتروستاتیکی کایتوزان در سوسپانسیون خمیرکاغذ درنظر گرفته شد. نتایج نشان داد، ویژگی های فرایندی (آبگیری از ورقه الیاف و ماندگاری نرمه در گذر اول) تحت تاثیر بار الکتروستاتیکی کایتوزان در محیط خنثی و قلیایی وضعیت بهتری داشته اند. به نظر می سد، با تغییر هرچه بیشتر pH سوسپانسیون به سمت خنثی و قلیایی، ازشدت بار مثبت الکتروستاتیکی کایتوزان و انحلال کاسته شده و به عکس بر بار منفی الیاف افزوده می شود. احتمالا این وضعیت بر نحوه اتصال پلیمر کایتوزان روی الیاف (حالت دم و لوپ)- به صورتی که در تشکیل فلاک موثرتر عمل نماید- تاثیر داشته است؛ به طوری که در شرایط خنثی میزان آبگیری و ماندگاری به ترتیب به میزان هرکدام 5/37 و 8/36 درصد نسبت به تیمار شاهد، 34 و 7 درصد نسبت به حالت اسیدی افزایش نشان داده است. همچنین هرچند سیستم مزبور در افزایش ویژگی‌های مقاومتی نسبت به تیمار شاهد کاملا موفقیت آمیز بوده است، اما تغییرات بار الکتروستاتیکی توسط pH بر ویژگی های مقاومتی (جز افزایش در مقاومت پیوند درونی) تاثیر مثبت اندکی داشته است.}, keywords_fa = {کایتوزان,بار الکتروستاتیکی,ویژگیهای فرایندی و مقاومتی,نانوسیلیکا,الیاف بازیافتی}, url = {https://www.ijwp.ir/article_31254.html}, eprint = {https://www.ijwp.ir/article_31254_1ca03b63b1f77816ff429276cc4d2dc2.pdf} }