@article { author = {Salehpour, Shuboo and Taremian, Asghar}, title = {Effect of Drying Method on the Permeability Coefficient of Oak Wood (Quercus infactoria)}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {1-9}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this study, the effect of drying method on the permeability coefficient of the oak wood (Quercus infectoria Oliv) was studied. Freshly-cut logs of oak were prepared from Oureman, the east area of Kourdistan in Iran. Then, boards with nominal thickness of 6 cm were cut. The boards were dried using two methods. In the first method, the boards were air dried to the moisture content close to FSP for 45 days and then they were kiln dried using T5-D1 schedule. In the second method, the boards were dried from green condition to the final moisture content of 10% using T5-D1 schedule. Then, the permeability coefficient in the transverse and longitudinal directions in both heartwood and sapwood regions was measured, separately. Results showed that the permeability of oak boards dried by kiln drying method both in the transverse and longitudinal directions and also in the heartwood and sapwood regions was greater than that of those dried by the combined method (air drying + kiln drying).}, keywords = {Drying,oak,Permeability coefficient,Sapwood,Heartwood}, title_fa = {اثر روش چوب‌خشک‌کنی بر ضریب نفوذپذیری چوب بلوط (Quercus infactoria)}, abstract_fa = {این تحقیق به‌منظور بررسی اثر روش چوب‌خشک‌کنی بر ضریب نفوذپذیری چوب بلوط (Quercus infactoria) انجام شد. گرده‌بینه‌های تازه بریده‌شده بلوط از اورمان (هورامان تخت) واقع در شرق کردستان تهیه و سپس به تخته‌هایی با ضخامت اسمی 6 سانتی‌متر تبدیل شدند. تخته‌ها با دو روش مختلف خشک شدند. درروش اول (روش ترکیبی)، تخته‌ها به مدت 45 روز در هوای آزاد تا میانگین رطوبت 30 درصد و سپس در کوره نیمه‌صنعتی با روش جابجایی هوای گرم و طبق برنامه T5-D1 تا رطوبت نهائی 10درصد خشک شدند. در روش دوم، تخته‌ها از میانگین رطوبت سبز 55 درصد تا رطوبت نهائی 10 درصد با برنامه T5-D1 در کوره خشک‌شدند. سپس، ضریب نفوذپذیری تخته‌های خشک‌شده در دو جهت عرضی و طولی و در دو ناحیه چوب‌برون و چوب‌درون به‌طور مجزا اندازه‌گیری شد. نتایج نشان داد که نفوذپذیری تخته‌های بلوط خشک‌شده در کوره در هر دو جهت طولی و عرضی و نیز در هر دو ناحیه چوب‌برون و چوب‌درون بیشتر از نفوذپذیری تخته‌های خشک‌شده با روش خشک‌کردن ترکیبی (هوای آزاد+ کوره) است}, keywords_fa = {خشک‌کردن,بلوط,ضریب نفوذپذیری,چوب‌برون,چوب‏درون}, url = {https://www.ijwp.ir/article_11256.html}, eprint = {https://www.ijwp.ir/article_11256_6188a394265c023b9033295f7819e9fb.pdf} } @article { author = {Madhoushi, Mehrab and Daneshvar, Soheila}, title = {Evaluation of Modulus of Elasticity in Standing Trees and Sawn Wood in Populous deltoids using Nondestructive Stress Wave Testing}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {11-20}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The aim of this paper was to evaluate relationship between dynamic modulus of elasticity (MOEd) in healthy standing trees of Populus deltoides and static modulus of elasticity (MOEs) of sawn lumber from the same standing trees, using nondestructive stress wave testing (NDT). For this purpose, NDT stress wave technique was used. The study was performed on 10 healthy standing trees of Populus deltoides. The diameter of trees at the breast height was selected at two categories, namely 25-30 cm and 30-35 cm. Measurement of wave velocity in standing trees were done transversely in radial direction at two geographical directions as North-South and East-West at the breast height, namely 130 cm and longitudinal measurements were done on the height between 80 and 180 cm. Then, standing trees were cut following by measurements of wave velocity in their logs. Logs were kept for two months after cutting in order to reduce moisture content. Then, they were cut into the clear specimens for statistical bending test and their MOE were evaluated according to ASTM standard. The results showed that the stress wave velocity and dynamic modulus of elasticity in longitudinal direction of standing trees and logs were more than those in transverse directions. Also, stress wave velocity and dynamic modulus of elasticity of the logs were higher than those in their standing trees at both directions. Finally, regression analysis indicated that the correlation coefficient between MOEd in standing trees and logs at diameter 30-35 cm is (r= 0.94), which is statistically significant.}, keywords = {Dynamic modulus of elasticity,Static modulus of elasticity,NDT stress wave}, title_fa = {ارزیابی رابطه بین مدول الاستیسیته درختان سرپا و چوب استحصال شده صنوبر دلتوئیدس با استفاده از آزمون غیرمخرب موج‌تنش}, abstract_fa = {هدف این مقاله ارزیابی رابطه بین مدول الاستیسیته دینامیکی (MOEd) در درختان سرپای سالم صنوبر دلتوئیدس و مدول الاستیسیته استاتیکی (MOEs) چوب استحصال شده از آن با استفاده از آزمون غیرمخرب موج‌تنش می‌باشد. مطالعه بر روی 10 پایه درخت سرپای صنوبر دلتوئیدس انجام شده‌است. قطر تنه درختان در ارتفاع برابر سینه در 2 کلاسه قطری 30-25 و 35-30 انتخاب شد. اندازه‌گیری سرعت موج‌تنش در درختان سرپا در جهت عرضی در دو جهت جغرافیایی شمال- جنوب و شرق- غرب در ارتفاع برابر سینه 130سانتی متر و اندازه‌گیری در جهت طولی نیز در ارتفاع 80 تا 180 سانتی‌متر انجام گرفت. سپس درختان قطع شدند و اندازه‌گیری‌های سرعت موج تنش بر روی گرده‌بینه‌ها نیز انجام شد. گرده‌بینه‌ها بعد از قطع، به مدت 2 ماه به منظور کاهش مقدار رطوبت نگهداری و سپس به آزمونه‌های کوچک برای انجام آزمون خمش استاتیکی و محاسبه MOE مطابق استاندارد ASTM تبدیل شدند. نتایج نشان دادند که سرعت موج تنش و  MOEdدرجهت طولی در درختان سرپا و گرده‌بینه‌ها بیش از جهت عرضی درخت سرپا می‌باشد. همچنین، سرعت موج تنش و MOEd در گرده‌بینه‌ها بیشتر از درختان سرپا در هر دو جهت می‌باشد. سرانجام‌، آنالیز رگرسیونی نشان داد که ضریب همبستگی MOEd درختان سرپا و گرده‌بینه‌ها در کلاسه قطری 35-30 در جهت عرضی (94/0r=) می‌باشد، که به طور آماری معنی‌دار است.}, keywords_fa = {مدول‌الاستیسیته دینامیکی,مدول‌الاستیسیته استاتیکی,آزمون غیرمخرب موج‌تنش}, url = {https://www.ijwp.ir/article_11257.html}, eprint = {https://www.ijwp.ir/article_11257_3c7254af6de202e2f06110ca79461884.pdf} } @article { author = {Dalvand, Mosayeb and Maleki, Sadegh and Ebrahimi, Ghanbar and Rostampour, Akbar}, title = {Investigating the Stress Carrying Capacity of Corner Joints In The Furniture Frame Fabricated With Dowel}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {21-32}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The goal of this study was to determine stress carrying capacity of doweled corner joints in framed furniture structures. Joint members were out of European silver Fir (Abies alba) and dowels were made from Beech and Hornbeam woods as variables in this study. Diameter of dowel had three levels in size, namely 6, 8 and 10 mm. Mitered and Butted experimental joints were tested under diagonal tension and compression loads. Results have shown that stress carrying capacity of tested joints under compressive load is more than that of tension one. Also, stress carrying capacity of mitered joints, under both loading type, was more than that of butted joints. Maximum stress capacity under tension load was observed in mitered joints with dowels of hornbeam which were 8 mm in diameter. Under compressive loads, maximum stress capacity was determined in mitered joints fabricated with dowels out of beech which were 8 mm in diameter. With tension loading, changing diameter of dowels from 6 to 8 mm, stress capacity of joint did increase drastically but from 8 to 10 mm, had no significant effects on joints’ capacity. Under compressive load, changing diameter of dowels from 6 to 10 mm had significant effect on capacity of joints. Species of dowel’s wood was not effective in tension, but in compression dowels of beech wood had pronounced improvement on joints’ capacity.}, keywords = {Stress carrying capacity,Wooden dowel,Miter joint,Butt joint,Diameter dowel}, title_fa = {بررسی ظرفیت تحمل تنش اتصال‌های گوشه‌ای با پین در قاب سازۀ مبلمان}, abstract_fa = {این پژوهش با هدف تعیین ظرفیت تحمل تنش اتصال‌های گوشه‌ای با پین چوبی در قاب سازۀ مبلمان صورت گرفته است. اعضای اتصال از چوب نراد بودند و پین‌ها از گونه راش و ممرز ساخته شدند. قطر پین در سه سطح به اندازه اسمی 6، 8 و 10 میلی‌متر بود. اتصال‌های آزمونی فارسی و سربه‌سر زیر بار کششی و فشاری قرار گرفتند. نتایج نشان دادند که ظرفیت تحمل تنش اتصال آزمون شده زیر بار فشاری بیشتر از ظرفیت تحمل تنش زیر بار کششی است. همچنین ظرفیت تحمل تنش اتصال فارسی در دو حالت بارگذاری (کششی و فشاری) نسبت به اتصال سربه‌سر بیشتر بوده است. بالاترین میزان ظرفیت تحمل تنش زیر بار کششی در اتصال فارسی با پین ممرز به قطر 8 میلی‌متر مشاهده‌شده است. بالاترین میزان ظرفیت تحمل تنش زیر بار فشاری مربوط به اتصال فارسی با پین راش به قطر 8 میلی‌متر بوده است. در بارگذاری کششی با تغییر قطر پین از 6 به 8 میلی‌متر ظرفیت تحمل تنش روند صعودی داشته است ولی افزایش قطر پین از 8 به 10 میلی‌متر تأثیر معنی‌داری بر ظرفیت تحمل تنش اتصال زیر بار کششی نداشته است. تغییر قطر پین از 6 به 10 میلی‌متر تأثیر معنی‌داری بر ظرفیت تحمل تنش زیر با فشاری داشته است. گونه چوب پین تأثیر معنی‌داری بر ظرفیت تحمل تنش زیر بار کششی نداشته است، ولی پین راش زیر بار فشاری دارای ظرفیت تحمل تنش بیشتری بوده است}, keywords_fa = {ظرفیت تحمل تنش,پین چوبی,اتصال فارسی,اتصال سربه‌سر,قطر پین}, url = {https://www.ijwp.ir/article_11258.html}, eprint = {https://www.ijwp.ir/article_11258_b5a522e02b1fae29d17d3e8d209aa7a3.pdf} } @article { author = {Ghofrani, Mohammad and Manavi, Gholamhossein and Mirshokrai, Ahmad}, title = {Investigation on the Scratch Strength of Clear Paints Used in Furniture Industries on the Wood Species Beech, Elm, Alder and Spruce}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {33-44}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In This research, the scratch strength (Cross-Cut Test) of clear paints (nitrocellulose lacquers and acid catalyst lacquers) of wood species Beech, Elm, Alder and spruce were studied as a function of moisture content (MC) of the samples. For this purpose, lumbers (550×110×12 mm) were cut from sapwood in tangential surfaces and were air dried for one month according to wood drying procedures. Then, for pre-conditioning of moisture content, at the levels of 8%, 12% and 15%, the samples were placed in three clima rooms. Then, finish applied and strength tests were performed. The results revealed that for acid catalyst lacquers the highest scratch strength (10.4%) belongs to Elm wood with 8% moisture content, and the lowest scratch strength (53.6%) belongs to Spruce wood with nitrocellulose lacquers having 15% moisture content.}, keywords = {: Scratch strength,Clear paints,Wood species,Nitrocellulose lacquers,Acid catalyst lacquers}, title_fa = {بررسی مقاومت به چسبندگی رنگ‌های شفاف رایج در صنایع مبلمان بر روی گونه‌های چوبی راش، ملج، توسکا و نوئل}, abstract_fa = {در این تحقیق، مقاومت به چسبندگی (آزمون خراش- نوارچسب Cross-Cut) رنگ‌های شفاف سیلر- کیلر و سیلر- نیم پلی‌استر، و با توجه به درصدرطوبت، در گونه‌های چوبی‌راش (Fagus orientalis)، ملج (Ulmus smontana)، توسکا (Alnus glutinosa) و نوئل (Picea  glauca) مورد مطالعه قرارگرفت. تخته‌هایی به ابعاد 12×110×550 میلی‌متر از قسمت برون چوب و از تخته مماسی تهیه شدند و به مدت یک ماه با رعایت اصول روش‌های چوب خشک کنی در هوای آزاد قرار گرفتند. سپس برای متعادل‌سازی رطوبت، به طور مجزا برای رسیدن به رطوبت 8، 12 و 15% در سه اتاق کلیما قرار داده شدند. تمامی سطوح نمونه‌ها با استفاده از پیستوله رنگ‌کاری شدند و آزمون‌های‌ مقاومت به خراش بر روی آن‌ها انجام شد. نتایج نشان داد که بیشترین مقدار مقاومت به خراش، با درصد از دست دادن چسبندگی 4/10%، مربوط به رنگ سیلر- نیم پلی‌استر استفاده شده بر روی گونه‌ی چوبی ملج با رطوبت 8% و کمترین مقدار مقاومت به خراش با درصد از دست دادن چسبندگی 6/53%، مربوط به رنگ سیلر- کیلر استفاده شده بر روی گونه‌ی چوبی نوئل با رطوبت 15% بوده‌است. }, keywords_fa = {مقاومت به چسبندگی,رنگ‌های شفاف,گونه‌ی چوب,سیلر,کیلر,نیم‌پلی-استر}, url = {https://www.ijwp.ir/article_11260.html}, eprint = {https://www.ijwp.ir/article_11260_96bcb34c9c76bccf0dccd15de700f4b3.pdf} } @article { author = {Rangavar, Hossein and Payan, M.Hassan and Khojaste, Saeid}, title = {Investigation of the type and content of gypsum on the dimensional stability and mechanical properties of gypsum particleboard}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {45-54}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this study in order to investigate the effect of gypsum type on the physical and mechanical properties of gypsum Particleboard were used from two type Jebel and Micronize gypsum. To obtain the suitable amount of gypsum in manufacturing gypsum particleboard was used from the three levels 2.5:1, 2.75:1 and 3:1 of gypsum to dried mass of wooden materials. Physical and mechanical properties of manufactured board were carried out in accordance with European Norms (EN) standard. The result showed that gypsum particleboard manufactured Jebel gypsum have the most mechanical properties (Bending strength, modulus of elasticity and internal bond strength), but physical properties (water absorption and thickness swelling) of this boards was more than the boards manufactured from Micronize gypsum. Furthermore using 2.75 times gypsum to dried mass of wooden materials is also suitable in production gypsum particleboard.}, keywords = {Gypsum particleboard,Jebel gypsum,Micronize gypsum,Gypsum content,Physical and mechanical properties}, title_fa = {بررسی تأثیر نوع و مقدار گچ بر ثبات ابعادی و خواص مکانیکی تخته‌های چوب گچ}, abstract_fa = {در این تحقیق به منظور بررسی تأثیر نوع گچ بر خواص فیزیکی و مکانیکی چند سازه چوب گچ، از دو نوع گچ ساختمانی (جبل) و گچ میکرونیزه استفاده گردید. همچنین برای به دست آوردن مقدار مناسب گچ در ساخت تخته‌ها از سه سطح 5/2، 75/2 و 3 برابر گچ نسبت به جرم خشک ماده چوبی استفاده شد. خواص فیزیکی و مکانیکی تخته‌های ساخته شده بر اساس استاندارد اروپا (EN) بررسی گردید. نتایج به دست آمده از این مطالعه نشان داد که تخته‌های ساخته شده با گچ ساختمانی (جبل) خواص مکانیکی (مقاومت خمشی، مدول‌الاستیسیته و  مقاومت چسبندگی داخلی) بیشتری داشتند اما خواص فیزیکی (واکشیدگی ضخامت و جذب آب) آن‌ها در مقایسه با تخته‌های ساخته شده با گچ میکرونیزه بیشتر بود. همچنین مقدار مناسب استفاده از گچ در ساخت تخته‌های چوب گچ 75/2 برابر نسبت به جرم خشک خرده چوب‌ها به دست آمد}, keywords_fa = {چندسازه چوب گچ,گچ جبل,گچ میکرونیزه,مقدار گچ,خواص فیزیکی و مکانیکی}, url = {https://www.ijwp.ir/article_11263.html}, eprint = {https://www.ijwp.ir/article_11263_d64eb89808bf58efe69b03b90245a7cf.pdf} } @article { author = {Rassam, Ghonche and Taghiyari, H.Reza and Keshtegar, Ali and Kool, Farhad}, title = {Effect of Nano bentonite on Fire Retardant Properties of Medium density fiberboard (MDF)}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {55-62}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In the present study, Fire – Retarding properties of nano-bentonite in medium density of fiberboard (MDF) was studied. 10% of urea-formaldehyde resin was used as the adhesive of the matrix. Nano Bentonite at 5 levels (0%, 5%, 10%, 15% and 20%) g/kg based of dry weight of fibers was used with the consumption of Urea-Formuldehyde (UF). Press pressure of 150 bar and temperature of 170during 4, 5, and 6 minutes were applied. Density was kept constant at 0.7 g/cm3 in all treatments. The measured properties consisted of mass reduction, inflammation time, fire-endurance, melting time and the burnt area. The results revealed that Nano-Bentonite had significant effect in approving fire retarding properties in medium density fiber board. The best properties at the level of 10% obtained and the same level recommended for industry use. The use of Nano-Bentonite more than 10% decreased the stickiness and the partly surface of fiberboards. }, keywords = {Medium-Density Fiberboard (MDF),Nano-Bentonit,Fire-Retarding Properties,Inflammation}, title_fa = {بررسی تاثیرذرات نانو بنتونیت بر روی خواص کندسوز کنندگی تخته فیبر با دانسیته متوسط (MDF)}, abstract_fa = {در این تحقیق خواص مقاومت به آتش تخته فیبر با دانسیته متوسط تیمارشده با نانوذرات بنتونیت مورد بررسی قرار گرفت. چسب استفاده شده در این تحقیق رزین اوره فرمالدهید به میزان 10%، و نانو بنتونیت در 5 سطح (0%، 5%، 10%، 15%، 20%) بر مبنای وزن خشک الیاف و به صورت مخلوط با رزین اوره فرمالدهید مورد استفاده قرارگرفت. فشار پرس 150 بار، دمای پرس 170 درجه سانتی‏گراد و در مدت زمان‌های 4، 5 و 6 دقیقه اعمال گردید. دانسیته تمامی تخته‏ها 7/0 گرم بر سانتی‏متر مکعب بود. خواص اندازه‏گیری‌شده شامل درصد کاهش وزن، زمان اشتعال، دوام شعله، زمان گدازش، و سطح کربونیزه‌شده بود. نتایج نشان داد که نانوبنتونیت تاثیر معناداری در بهبود خواص کندسوزی تخته‌فیبر با دانسیته‌ی متوسط دارد؛ بهترین خواص در سطح 10% به دست آمد و از این رو همین سطح برای استفاده در بخش صنعت توصیه می‌شود. استفاده از نانوبنتونیت بیش از 10% باعث کاهش چسبندگی و پرز دار شدن سطح تخته‏ها می‏شود.}, keywords_fa = {تخته فیبر با دانسیته متفاوتMDF) ),نانو بنتونیت,کند سوزکنندگی,اشتعال}, url = {https://www.ijwp.ir/article_11267.html}, eprint = {https://www.ijwp.ir/article_11267_3a8e6ab508507d5beb978fe8a0373739.pdf} } @article { author = {Daii, Sahar and Tabarsa, Taghi and Shakeri, Alireza}, title = {Investigating on Effect of Particle Form and Mixing Method on applied Properties Green Composite}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {63-74}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Nowadays Paulownia as the fast growing species has noticed for wood industry in the world. In this research, Paulownia fortuni planted in Shaskolateh forest of Gorgan were studied. Two particle form, flour (60 mesh size) and fiber (RMP, L/D= 21/54) were prepared. 60 percent of this material with 37% of HDPE , 3% of MAPE were blended separately. Part from this material by internal mixer and other part by extruder blended. Output was prepared like pellets. Samples were prepared in dimensions of 30cm×30cm×1cm, and nominal density 1 g/cm3 by hot press. The mechanical testing of the panels (flexural, hardness, unnotched impact strength) and the physical testing of the panels (thickness swelling and water absorption after 2 & 24 hours immersion in water) were measured. The result showed that modulus of rupture, hardness, unnotched impact strength of composite made of fiber-PE were lower than composite made of flour-PE. Flexural elastic modulus of composite made of fiber-PE were higher than flour-PE. Water absorption and thickness swelling of composite made of fiber-PE were higher than flour-PE. Also physical and mechanical properties of composites blended by internal mixer improved in compared composites blended by extruder. Physical and mechanical properties of composite made of fiber-PE blended by internal mixer improved in compared composite made of fiber-PE blended by extruder.}, keywords = {Flour,Fiber,Internal mixer,Extruder,Composite}, title_fa = {بررسی تأثیر شکل ذرات و روش اختلاط بر ویژگی‌های کاربردی چندسازه سبز}, abstract_fa = {امروزه پالونیا به‌عنوان گونه‌ای تندرشد برای صنعت چوب در جهان مورد توجه قرارگرفته‌است. در این تحقیق ارزیابی روی پالونیا فورتونی کاشته شده در جنگل شصت کلاته گرگان انجام شد. دو شکل آرد (مش 60) و الیاف به‌دست‌آمده از روش مکانیکی (با ضریب کشیدگی54/21) آماده شد و60% این مواد به‌طور جداگانه با 37% HDPE و 3% MAPE با دو روش اختلاط مذاب مخلوط شدند. بخشی از اختلاط با دستگاه مخلوط‌کن داخلی و بخشی دیگر با دستگاه اکسترودر انجام شد. محصول به‌صورت گرانول آماده شد. نمونه‌های آزمونی به ابعاد cm1×cm30×cm30 با چگالی (دانسیته) اسمی g/cm3 1 با پرس گرم آماده شد. آزمون مکانیکی (خمش، سختی و ضربه بدون شکاف) و فیزیکی (جذب آب و واکشیدگی ضخامت) بر روی نمونه‌های آزمونی انجام گرفت. نتایج نشان داد مدول گسیختگی، سختی و ضربه چندسازه الیاف- پلیمر نسبت به چندسازه آرد- پلیمر کم‌تر شد. درصورتی‌که مدول کشسانی (الاستیسیته) خمشی چندسازه الیاف- پلیمر بیشتر از چندسازه آرد- پلیمر شد و میزان جذب آب و واکشیدگی ضخامت چندسازه الیاف- پلیمر بیشتر از چندسازه آرد- پلیمر به دست آمد. همچنین ویژگی‏های فیزیکی و مکانیکی چندسازه‌های اختلاط یافته با مخلوط‌کن داخلی در مقایسه چندسازه‌های اختلاط یافته با اکسترودر بهبود یافت. ویژگی‌های فیزیکی و مکانیکی چندسازه‌ الیاف- پلیمر اختلاط یافته با مخلوط‌کن داخلی در مقایسه با اکسترودر بهبود یافت.}, keywords_fa = {آرد,الیاف,مخلوط‌کن داخلی,اکسترودر,چندسازه}, url = {https://www.ijwp.ir/article_11270.html}, eprint = {https://www.ijwp.ir/article_11270_cd301ad475ac849ec19c9972922f5ed4.pdf} } @article { author = {Kord, Behzad and Yazdanparast, Kusha and Tazakor rezai, Vahid}, title = {Effect of Weathering Time on the Physical - Mechanical Properties and Color Change in Wood Flour/HDPE Composite}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {75-83}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {This study was carried out to investigate the effect of weathering time on the physical and mechanical properties and color change in composite made of wood flour and high density polyethylene (HDPE). For this purpose, wood flour and polyethylene at a weight ratio of 60:40 with coupling agent were compounded in an internal mixer, and the samples were made in injection molding. Then, the weathering process by ultraviolet irradiation and water spray was done on the samples at different times of 250, 500, 1000 and 2000 hours in accelerated weathering apparatus. Finally, the physical and mechanical properties and color measurement of samples were tested, and compared with control samples. Results indicated that the flexural strength, flexural modulus, tensile strength and tensile modulus decreased with an increase in weathering time; however, the water absorption increased. Also, the yellowness of wood plastic samples decreased with an increase in weathering time and due to the lightness and color change increased.}, keywords = {Weathering,wood plastic composite,Mechanical Strength,water absorption,lightness,color change}, title_fa = {بررسی تأثیر زمان هوازدگی بر ویژگی‌های فیزیکی، مکانیکی و تغییر رنگ چندسازه آرد چوب- پلی‌اتیلن سنگین}, abstract_fa = {این تحقیق، با هدف بررسی تأثیر مدت‌زمان هوازدگی بر ویژگی‌های فیزیکی، مکانیکی و تغییر رنگ چندسازه ساخته شده از آردچوب- پلی‌اتیلن سنگین انجام شد. برای این منظور، آرد چوب و پلی‌اتیلن با نسبت وزنی60 به 40 درصد به‌ همراه ماده سازگارکننده مالئیک‌دار در دستگاه مخلوط‌کن ‌داخلی ترکیب‌شده و نمونه‌های آزمونی با استفاده از روش قالب‌گیری تزریقی ساخته شد. سپس فرایند هوازدگی بر روی نمونه‌ها در دستگاه هوازدگی مصنوعی تحت اشعه فرابنفش همراه با اسپری آب در فواصل زمانی 250، 500، 1000 و 2000 ساعت قرار گرفتند. در نهایت آزمون‌های مکانیکی و فیزیکی و رنگ‏سنجی برروی نمونه‌‌ها انجام گرفت و نتایج آن با نمونه‌های شاهد (هوانزده) مقایسه شد. نتایج نشان داد که با افزایش مدت ‌زمان هوازدگی، مقاومت و مدول‌ خمشی، مقاومت و مدول کششی در نمونه‌ها کاهش یافته، در حالی‌که جذب آب و واکشیدگی ضخامت نمونه‏ها افزایش می‌یابد. همچنین نتایج نشان داد با افزایش مدت‌زمان هوازدگی از میزان زردی نمونه‌ها کاسته‌شده و به تبع آن میزان روشنی و تغییر رنگ در آنها افزایش می‌یابد}, keywords_fa = {هوازدگی,چندسازه چوب پلاستیک,مقاومت مکانیکی,جذب آب,روشنی,تغییر رنگ}, url = {https://www.ijwp.ir/article_11271.html}, eprint = {https://www.ijwp.ir/article_11271_73e32b4d435ac72e0b048086ecfcba27.pdf} } @article { author = {Jabbari, Mohammad and Tatari, A.Asghar and Ghafari, Mansour}, title = {Effect of Faces Type and Thickness on Mechanical Properties of Sandwich Panels}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {85-92}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Sandwich panels are new kind of layered composites that usually are composed of three layers and their core layers thickness is higher but the top layers are determinative indetermination of the products strength and stiffness. In this study, effect of faces type and thickness on mechanical properties of sandwich panels was investigated. The variables included, faces type with 3, 4 and 5 mm thickness (beech face, popular face) and adhesive type (PMDI). After making panels, sampling test (based on DIN- EN 326-1) was considered. Mechanical properties of panels included modulus of elasticity as well as module of rupture (based on DIN- EN 310 standard) and impact bending strength (IBS) (based on ASTM- D 3499 standard) were measured. The gathered data were analyzed as completely randomized factorial design. The results showed that, the thickness of faces has a significant effect on the mechanical properties. With increasing thickness of 3 to 5 mm, modulus of rupture, modulus of elasticity and impact bending strength (IBS) increased. The interaction effect between species and thickness showed that using of beech genus with 5 mm thickness leads to increase of mechanical properties in sandwich panels.}, keywords = {Sandwich Panels,Mechanical properties,PMDI,Layer Thickness,Beech and Popular}, title_fa = {بررسی تأثیر نوع و ضخامت رویه بر خواص مکانیکی پانل‌های ساندویچی}, abstract_fa = {پانل‌های ساندویچی گروه ویژه‌ای از فرآورده‌های لایه‌ای هستند که اغلب سه‏لایه بوده و مغزی آن‌ها دارای ضخامت بیشتری است، اما سفتی و صلبیتکمتری نسبت به‌ لایه پشت و رو دارند. در این پژوهش تأثیر نوع و ضخامت رویه بر خواص مکانیکی پانل‌های ساندویچی بررسی شده‌است. عوامل متغیر در این پژوهش شامل، نوع رویه (رویه راش و رویه صنوبر با ضخامت 3، 4 و 5 میلی‌متر) و چسب مصرفی (ایزوسیانات (PMDI) ) بوده‌است. پس از ساخت پانل‌ها، نمونه‌های آزمونی مطابق با استاندارد DIN آیین‌نامهEN 326-1  تهیه شدند. خواص مکانیکی پانل‌ها شامل مدول الاستیسیته و مدول گسیختگی مطابق با استاندارد DIN آلمان آیین‌نامه EN 310 و نیز مقاومت به ضربه پانل‌ها مطابق با استانداردASTM  آیین نامه D3499 اندازه‌گیری شد. تجزیه و تحلیل داده‌ها در قالب طرح آماری کاملاً تصادفی متعادل، تحت آزمون فاکتوریل صورت گرفت. نتایج این بررسی نشان داد که ضخامت رویه‌ها تأثیر معنی‌داری بر ویژگی‌های مقاومتی داشته‌است. با افزایش ضخامت رویه‌ها از 3 به 5 میلی‌متر مدول گسیختگی، مدول الاستیسیته و مقاومت به ضربه افزایش یافته‌است. با توجه به اثر متقابل بین گونه و ضخامت مشخص شده است که استفاده از گونه راش در ضخامت 5 میلی‌متر باعث حداکثر شدن مقاومت‌های مکانیکی در پانل‌های ساندویچی شده‌است}, keywords_fa = {پانل‌های ساندویچی,خواص مکانیکی,چسب ایزوسیانات,ضخامت لایه,راش و صنوبر}, url = {https://www.ijwp.ir/article_11276.html}, eprint = {https://www.ijwp.ir/article_11276_1804a46cf82eee16eb028f228e934715.pdf} } @article { author = {Rassam, Ghonche and Taghiyari, H.reza and Ebrahimi, Mastoureh}, title = {Study on the Effect of Combined Nanosilver- Hygrothermal Treatments on Wood Properties}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {93-106}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this research, the combined effect of impregnation of wood with nanosilver solution and hygrothermal treatment on some physical and mechanical properties of beech (Fagus orientalis Lipskey) and spruce (Piceaabies) woods was studied. Wood specimens, Initially, were impregnated in an impregnation cylinder for 20 minutes at the pressure of 0.25 MPa, with nanosilver solution. Then, hygrothermal treatment was carried out at the temperatures of 120, 150 and 180°C for 1, 3 and 5 hours. Control specimens, without any impregnation process, were hygrothermally treated. Volumetric Swelling after 2 and 24 hours soaking in water, bending strength, impact load resistance and compressive strength parallel to the grain of specimens were measured, according to ASTM D143 and all data were analyzed statistically. The results showed that swelling and mechanical properties were decreased by increasing the temperature and duration of hygrothermal treatment. Also, nanosilver impregnated specimens which were treated at 180 ˚C had lower swelling without Not clear and not seems. Consequently or it can be concluded that with nanosilver impregnation process of wood, hygrothermal treatment would be carried out at higher temperature (180 ˚C) to obtain better dimensional stability with no more decrease in mechanical properties.}, keywords = {hygrothermal treatment,Nano silver,Volumetric swelling,bending strength}, title_fa = {بررسی اثر ترکیبی تیمار نانونقره و تیمارحرارتی بخار گرمایی بر خواص چوب}, abstract_fa = {در این تحقیق اثر ترکیبی اشباع چوب با محلول نانونقره و تیمارحرارتی با بخارآب (بخار گرمایی) بر برخی خواص فیزیکی و مکانیکی چوب‏های راش (Fagus orientalis Lipsky) و نوئل (Picea abies) مورد ارزیابی قرارگرفت. نمونه‌های چوب ابتدا به مدت 20 دقیقه درفشار 25/0مگاپاسکال در سیلندر اشباع، توسط محلول نانو نقره اشباع شده و متعاقباً تحت تیمار بخار گرمایی دردماهای 120، 150 و 180 درجه سلسیوس و زمان1، 3 و 5 ساعت قرارگرفتند. نمونه‌های شاهد، بدون مرحله اشباع، فقط تحت تیمار بخار آب قرارگرفتند. واکشیدگی حجمی بعد از 2و 24 ساعت غوطه‌وری درآب، مقاومت خمشی، مقاومت به ضربه ومقاومت فشاری موازی با الیاف مطابق با ASTM D143  اندازه‌گیری شده و کلیه داده‌ها مورد تحلیل آماری قرار‌گرفت. نتایج به‌دست آمده حاکی از کاهش واکشیدگی و مقاومت‌های مکانیکی در نتیجه افزایش دما و زمان بخاردهی بود. همچنین، در نمونه‌های اشباع شده با محلول نانونقره و تیمارشده با افزایش زمان و دمای تیمار، مقدار واکشیدگی حجمی بعد از2و24 ساعت کاهش پیدا می‌کند. تیمار با نانو مقاومت‌ها را کاهش داده و زمان 5 ساعت و دمای 180 درجه‌سلسیوس نیز کم‌ترین مقاومت‌های مکانیکی را ایجاد می‌کند. به‌طورکلی نتایج نشان داد که با عمل اشباع چوب توسط محلول نانو‌نقره می‌توان تیمار بخارگرمایی را در دمای بالاتری (180 درجه‌سلسیوس) انجام داد تا ضمن رسیدن به ثبات ابعاد بهتر، مقاومت‌های مکانیکی چوبِ تیمار و اشباع‌شده کم‌تر کاهش یابد.}, keywords_fa = {تیماربخارگرمایی,نانو نقره,مقاومت خمشی,مقاومت فشاری موازی الیاف,واکشیدگی حجمی}, url = {https://www.ijwp.ir/article_11281.html}, eprint = {https://www.ijwp.ir/article_11281_a9a0c7835084ca8268628a93504ba11b.pdf} } @article { author = {Mehmandust, Mahboubeh and Khazaian, Abolghasem}, title = {Methods of retention increasing urea formaldehyde resin in order to produce wood-polymer from Paulownia}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {107-117}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {In this research, suitable treatment was studied for increasing resin retention in Paulownia wood. Retention amount of Paulownia with urea formaldehyde resin was studied after treatment by 3 type's solutions NaOH, NaCl and Urea with 1% and 2% concentrations in 20 and 40 0C during 4 and 8H. By 3 repeats for each treatment, totally 72 specimens with dimension 5×5×15 cm3 were provided. After performing pre-treatment, impregnation was done by urea formaldehyde resin and its polymerization. The results showed the precent of resin retention of the treatment specimens to control was increased and NaCl solution with 2% concentration in 20 0C and during 8H have been had the most effect on resin retention rate. Generally, pre-treatment causes to improve resin retention in Paulownia}, keywords = {Retention,Urea formaldehyde resin,Wood-Polymer,Paulownia}, title_fa = {روش‌های افزایش جذب رزین اوره فرمالدئید به منظور تولید چوب پلیمر از پالونیا}, abstract_fa = {در این پژوهش تیمارهای مناسب برای افزایش جذب رزین در چوب پالونیا مورد مطالعه قرار گرفته است. میزان جذب پالونیا با رزین اوره فرم‌آلدئید پس از تیمار با سه نوع محلول سدیم هیدروکسید، سدیم کلرید و محلول اوره، با غلظت‌های 1و2 درصد، در دماهای 20 و 40 درجه سانتیگراد و زمان 4 و 8 ساعت مورد بررسی قرار گرفت. با احتساب سه تکرار برای هر تیمار در مجموع 72 نمونه به ابعاد cm3 15×5×5 تهیه شد.پس از انجام پیش‌تیمار، اشباع با رزین اوره‌فرمالدئید و پلیمریزاسیون آن انجام گرفت. نتایج نشان داد که درصد جذب رزین نمونه‌های تیمار شده نسبت به شاهد افزایش یافته است و محلول سدیم کلرید با غلظت 2 درصد در دمای 20 درجه و زمان 8 ساعت بیشترین تاثیر را بر میزان جذب رزین داشته است. به طور کل پیش‏تیمار موجب بهبود جذب رزین در پالونیا می‌شود.  }, keywords_fa = {جذب,رزین اوره فرمالدئید,چوب پلیمر,پالونیا}, url = {https://www.ijwp.ir/article_11286.html}, eprint = {https://www.ijwp.ir/article_11286_bb87f1beb4801e9635b1f768e86fbdcd.pdf} } @article { author = {Hamzeh, Yahya and Abyaz, Ali and Abdolkhani, Ali and Hejazi, Sahhab and Izadyar, Soheila}, title = {Effect of Diluted Acid Pre-Extraction on Soda Pulping of Bagasse}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {119-128}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {Pre-extraction of hemicelluloses prior to pulping allows co-production of pulp and different hemicellulose-based chemicals in the chemical pulp mills. Due to important impact of hemicelluloses on pulp properties, their pre-extraction would be carried out in controlled conditions to minimize adverse effects on pulp properties. In this study, we focused on the effect of dilute acid pre-extraction on soda pulping and paper properties of bagasse to determine the optimum conditions for hemicelluloses extraction. The pre-extracted with dilute sulfuric acid was performed with 1, 2 and 4% of sulfuric acid concentration (w/v), liquid-to- solid ratio of 5, at 120, and 140 and 160 °C for 5, 10 and 15 minutes. Then, untreated and treated bagasse at selected condition were used to produce soda pulp with 11, 14 and 17% active alkali and then the selected pulps were bleached in ECF sequence. The pre-extraction results showed that dilute acid pre-extraction by 1% H2SO4, at 120 oC for 60 minute provided the best results regarding to extraction yield and residual holocellulose. However, screen yield, bleaching yield, tensile and burst strengths of obtained pulp from extracted bagasse were significantly lower than that obtained from unextracted bagasse, presumably due to considerable extraction of hemicelluloses.}, keywords = {: Bagasse,Acid Hydrolysis,Hemicelluloses,Pre-extraction,Soda pulping}, title_fa = {اثر پیش استخراج باگاس با روش اسید رقیق بر خمیرکاغذ حاصل از آن}, abstract_fa = {پیش استخراج همی‌سلولزها قبل از فرآیند تهیه خمیرکاغذ امکان تولید همزمان خمیرکاغذ سلولزی و مواد شیمیایی مبتنی بر همی‌سلولزها را در صنایع خمیرکاغذ امکان‌پذیر می‌کند. به دلیل اثر همی‌سلولزها بر خواص خمیرکاغذ، پیش استخراج آن‌ها باید در شرایط کنترل باشد تا کمترین اثر نامطلوب را بر ویژگی‌های خمیرکاغذ تولیدی داشته باشد. در این تحقیق اثرات پیش استخراج همی‌سلولزهای باگاس در شرایط اسید رقیق بر خمیرسازی و خواص خمیرکاغذ سودای باگاس بررسی شده‌است. پیش استخراج همی‌سلولزها با روش هیدرولیز اسیدی با اسید سولفوریک رقیق با غلظت 1 و 2 و 4 درصد، نسبت مایع به جامد 5، دمای 120 و 140 و 160 درجه سلسیوس به مدت 5 و 10 و 15 دقیقه انجام شد. تهیه خمیرکاغذ از باگاس پیش‌استخراج شده در شرایط منتخب و باگاس تیمار نشده در سه قلیائیت 11، 14 و 17 درصد قلیائیت فعال به روش سودا انجام شد و خمیرکاغذهای منتخب با روش ECF رنگبری شدند. نتایج نشان داد که پیش‌استخراج با روش اسید رقیق با غلظت 1% در دمای 120 درجه سلسیوس به مدت 5 و 15 دقیقه شرایط مناسب‌تری را از نظر بازده و مقدار کربوهیدرات‌های باقی‌مانده در باگاس به دست می‌دهد. نتایج تهیه خمیرکاغذ سودا نیز نشان داد که قلیائیت 17% در دمای 165 درجه سلسیوس به مدت یک ساعت شرایط مناسبی برای تهیه خمیرکاغذ قابل رنگبری از باگاس پیش‌تیمار شده و پیش‌استخراج نشده است. به‌علاوه، بازده پس از غربال، بازده رنگبری و مقاومت کششی و ترکیدگی کاغذهای حاصل از باگاس پیش‌تیمار شده به مقدار قابل‌توجهی کمتر از باگاس پیش‌استخراج شده بود که علت آن را می‌توان به حذف مقدار قابل‌توجهی از همی‌سلولزها در جریان پیش‌استخراج نسبت داد}, keywords_fa = {باگاس,هیدرولیز اسیدی,همی‌سلولزها,پیش‌استخراج,خمیرکاغذ سودا}, url = {https://www.ijwp.ir/article_11289.html}, eprint = {https://www.ijwp.ir/article_11289_1c08eddff721172f6eca70c258f5e0bd.pdf} } @article { author = {Afra, Elyas and Akbarpour, Iman and Hezbi, Nazbakht and Resalati, Hossein}, title = {Investigation of the Effect of Endoglucanase Treatment on Beatability and Drainage Rate of OCC Pulps}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {129-138}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {This research was performed to investigate of different endoglucanase levels and enzymatic treatment times on the beatability and drainage rate of OCC pulp. Endoglucanase enzyme with different dosages including 1u, 2u and 3u (on oven dry based pulp) at different times of 0.5, 1, 1.5 and 2 hours under constant process conditions added to OCC pulp in two states namely refined and unrefined. Treated pulps under different conditions were evaluated at the point of beatability and drainage rates. The results showed that addition of enzyme caused to improve (confidence level of 95%) freeness and drainage rate, compared to control sample but improvement of freeness with increasing of endoglucanase dosages was not observed significantly. The results of the effect of different enzyme levels at different refining levels was shown that addition of different enzyme dosages to pulps refined at different levels, caused to improve freeness and drainage rate. With increasing the degree of pulps refining (higher levels of refining), the effect of enzyme concentration was observed a little to improve freeness and drainage rate. Also in total refining levels, longer treatment by enzyme from up to 1 hours (using optimum dosage 1u) was led a significant effect on increasing the freeness while there was not a significant decrease of freeness at longer times than 1 hour.}, keywords = {OCC pulp,endoglucanase enzyme,beatability,drainage rate}, title_fa = {بررسی تأثیر تیمارآنزیمی اندوگلوکاناز بر پالایش‌پذیری و سرعت آب‌گیری خمیرکاغذ OCC}, abstract_fa = {در این تحقیق تأثیر مقادیر مختلف آنزیم اندوگلوکاناز و زمان‌های مختلف تیمار آنزیمی بر ویژگی‌های پالایش‌پذیری و سرعت آب‌گیری خمیرکاغذ OCC مورد بررسی قرار گرفت. آنزیم اندوگلوکاناز با مقادیر مختلف u1، u2 و u3 (برپایه وزن خشک خمیرکاغذ) در مدت‌ زمان‌های0، 5/0، 1، 5/1 و2 ساعت در شرایط ثابت فرآیندی به خمیرکاغذ OCC در دو حالت پالایش‌‌شده و پالایش‌نشده افزوده‌شد. خمیرکاغذهای تیمار شده در شرایط مختلف به لحاظ ویژگی‌های پالایش‌پذیری و سرعت آب‌گیری در مقایسه با خمیرکاغذ شاهد (خمیرکاغذOCC تیمارنشده با آنزیم) ارزیابی شدند. نتایج به‌دست‌آمده نشان داد که افزودن آنزیم موجب بهبود معنی‌دار (سطح اعتماد 95%) درجه روانی خمیرکاغذ OCC در مقایسه با نمونه شاهد شد، اما بهبود درجه‌روانی با افزایش غلظت آنزیم مصرفی، معنی‌دار نشده‌است. نتایج به‌دست‌آمده از تأثیر مقادیر مختلف آنزیم در سطوح مختلف پالایش نشان داد که افزودن سطوح مختلف آنزیم در خمیرکاغذهای پالایش‌شده در دورهای مختلف موجب بهبود معنی‌دار درجه‌روانی و سرعت آب‌گیری خمیرکاغذ شد. تأثیر افزایش غلظت آنزیم در بهبود درجه‌روانی و سرعت آب‌گیری با افزایش میزان پالایش خمیرکاغذ (سطوح بالاتر پالایش) کم‌تر دیده‌ شده‌است. همچنین در همه سطوح پالایش به کار گرفته‌شده، طولانی‌شدن زمان تیمار آنزیمی از 5/0 به 1ساعت (با مصرف میزان بهینه u1 آنزیم) تأثیر معنی‌داری را در افزایش درجه‌روانی خمیرکاغذ نتیجه داد اما در زمان‌های بیشتر از 1ساعت، کاهش درجه روانی معنی‌دار نبوده‌است}, keywords_fa = {خمیرکاغذOCC,آنزیم اندوگلوکاناز,پالایش‌پذیری,سرعت آب‌گیری}, url = {https://www.ijwp.ir/article_11292.html}, eprint = {https://www.ijwp.ir/article_11292_cc3146cf39efd6232b8411599f175250.pdf} } @article { author = {Pouryazdian, Ebrahim and Serayian, Ahmad and Dehghani, M.reza}, title = {The Comparison of Kraft Pulp Properties from Stem and Branchwood of Hornbeam}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {139-152}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The utilization of tree branches as potential resource of fibers, that can be supply raw materials for pulp and paper industries, additionally, increases the productivity of tree. This research was done in order to compare pulp and paper properties from branch wood and stem wood and feasibility utilization that in pulp and paper industries. Stem and branch wood samples of hornbeam with mean diameter about 15 cm were obtained from Shastkolateh educational forest (Gorgan).The measurement of fibers was done with using Franklin method and light microscopic and chemical compositions were determined according to TAPPI test methods. The Kraft pulps from stem and branch wood were prepared under constant condition include sulfudity 20%, Max temp 170˚C and Liquor to wood ratio 5/1 and variable condition include active alkali 14%, 16% and 18%, and cooking time of 90, 120 and 150 min. Ultimately mechanical properties of Handsheet were measured according TAPPI test method The statistical analysis of results indicated that independent effects of wood, active alkali, and time were significant on pulp yield and Kappa number. Comparing the pulp yield and Kappa number means were showing that yield of stem wood pulp is higher than branch wood and its kappa number is less. Analysis mechanical properties on stem and branch wood Hand sheets showed that mechanical properties of Hand sheet from stem wood are higher than branch wood. There is none meaningful difference between the most mechanical properties hand sheets of stem and branch wood, that produced under cooking condition include sulfudity 20%, active alkali 18% and cooking time 150 min. therefore this condition would suggest for simultaneous cooking branch and stem wood}, keywords = {hornbeam,kraft pulp,Stem wood,Branch wood}, title_fa = {مقایسه ویژگی‌های خمیر کاغذ کرافت حاصل از تنه و شاخه ممرز}, abstract_fa = {استفاده از شاخه‌های درخت به عنوان یک منبع بالقوه فیبری، علاوه بر اینکه می‌تواند بخشی از مواد اولیه مورد نیاز صنایع خمیر و کاغذ تامین کند، راندمان هر درخت را نیز افزایش می‌دهد. این پژوهش با هدف مقایسه ویژگی‌های خمیر کاغذ کرافت چوب تنه و شاخه ممرز و امکان استفاده از شاخه در صنایع خمیر کاغذ انجام گرفت. نمونه‌های چوب تنه و شاخه به قطر تقریبی 15 سانتیمتر از جنگل آموزشی شصت‌کلا‌ته (گرگان) تهیه گردید. اندازه‌گیری الیاف با استفاده از روش فرانکلین و میکروسکوپ نوری و ترکیبات شیمیایی چوب براساس دستورالعمل TAPPI صورت پذیرفت. خمیر کاغذ کرافت چوب تنه و شاخه تحت شرایط ثابت سولفیدیته 20 درصد، دمای حداکثر 170 درجه سانتیگراد و نسبت مایع پخت به چوب 5 به 1 و شرایط متغیر قلیائیت فعال 14، 16 و 18 درصد، زمان پخت 90، 120 و 150 دقیقه تهیه گردید، سپس در محدوده عدد کاپا 20، 25، 30 اقدام به تهیه کاغذ دست‌ساز شد. در نهایت خواص مقاومتی کاغذهای دست‌ساز براساس دستورالعمل TAPPI اندازه‌گیری شد. ارزیابی آماری نتایج نشان می‌دهد که اثر مستقل نوع چوب، زمان و قلیائیت فعال بر عدد کاپا و بازده خمیر معنی‌دار می‌باشد. مقایسه میانگین بازده و عدد کاپای خمیرها نیز نشان می‌دهد بازده خمیر کاغذ چوب تنه بیشتر از چوب شاخه و عدد کاپای آن کمتر می‌باشد. بررسی خواص مقاومتی کاغذ دست‌ساز تنه و شاخه نشان داد ویژگی‌های مقاومتی کاغذ دست‌ساز تنه بیشتر از شاخه می‌باشد. بین ویژگی‌های مقاومتی کاغذ دست‌ساز تنه و شاخه در شرایط پخت سولفیدیته 20%، قلیائیت فعال 18% و زمان پخت 150 دقیقه تفاوت معنی‌داری وجود ندارد. این شرایط، برای پخت همزمان تنه و شاخه ممرز پیشنهاد می‌شود}, keywords_fa = {ممرز,خمیر کاغذ کرافت,چوب تنه,چوب شاخه}, url = {https://www.ijwp.ir/article_11295.html}, eprint = {https://www.ijwp.ir/article_11295_1dc11489eac4b7641294af2a42174f18.pdf} } @article { author = {Rangavar, Hossein and Kh.khosro, Saeid}, title = {Investigating the Effective Index on Customers Choice in Buying Furniture}, journal = {Iranian Journal of Wood and Paper Industries}, volume = {5}, number = {1}, pages = {153-164}, year = {2014}, publisher = {Iranian Scientific Association of Wood and Paper Industries}, issn = {2008-9066}, eissn = {2423-3242}, doi = {}, abstract = {The competitive world today, with increasing customers satisfaction and expanding the definition of hosting and its direct connection with quality of products is essential. Thus not only the current customers stay fixed but also it increases. The purpose of this study was to investigate and ranking the crucial indicators that influence the choice of furniture by customers. Because of this, the studied indexes are classified in 6 group: quality, beauty, design, creating a suitable atmosphere for selling the goods, selling conditions and advertising. Population consisted of three major commercial areas in Tehran (Delawaran, Hassan Abad and Yaftabad). Statistical sample consisted a number of 100 people. A questionnaire was developed to gather data. Reliability of the questionnaires has been approved through Cronbach's Alpha coefficient (0.921). Investigation of effective indexes was done by chi-square method and in order to final ranking the indexes, friedman analyses have been used. The results obtained of ranking showed the chief factor in customers choice is under category of beauty due to this elegancy role in customers point of view. After elegancy, according to the classified elements studied in this research, raw material in making furniture, wood production’s price, ergonomy, customers satisfaction for his last purchase and immediate delivery, respectively, are the most important effective index in buying furniture by consumer.}, keywords = {: Household wooden furniture,Friedman analyses,index,Buying,Consumers}, title_fa = {بررسی شاخص‌های مؤثر بر انتخاب مشتری در خرید مبلمان چوبی منزل}, abstract_fa = {در دنیای رقابتی امروز برای صاحبان صنایع با بالا رفتن اهمیت رضایت مشتری و گسترش آن، مفهوم مشتری‌مداری و رابطه مستقیم آن با کیفیت محصولات تولید شده یک ضرورت است. بدین‌ترتیب نه‌ تنها تعداد مشتریان فعلی حفظ بلکه افزایش خواهند یافت. هدف از این مطالعه، شناسایی و رتبه‌بندی شاخص‌های مؤثر و تأثیرگذار بر انتخاب مشتری در خرید مبلمان چوبی منزل بود که در قالب شش شاخص اصلی شامل: کیفیت، زیبایی، طراحی، خدمات پس از فروش، شرایط فروش و تبلیغات تحت بررسی قرار گرفتند. جامعه آماری این مطالعه، خریداران مبلمان از سه نقطه مهم تجاری شهر تهران شامل دلاوران، حسن‌آباد و یافت‌آباد بودند. حجم نمونه‌های مورد بررسی100 نفر تعیین شد. ابزار گردآوری داده‌ها در این مطالعه پرسش‌نامه بوده و همبستگی سؤالات پرسش‌نامه‌ها با ضریب آلفای کرونباخ 921/0 تأیید شد. برای بررسی تأثیر شاخص‌های مورد مطالعه بر خرید مبلمان از روش کی‌دو (x2) استفاده شد و رتبه‌بندی نهایی شاخص‌های مؤثر بر انتخاب مشتری با آزمون فریدمن انجام پذیرفت. نتایج حاصل از رتبه‌بندی صورت گرفته نشان داد که مهم‌ترین شاخص مؤثر در انتخاب مشتری معیار‌های مربوط به زیر مجموعه زیباییمحصول است. در این زمینه عامل ظرافت نقش بسزایی را در خرید مبلمان از نقطه‌ نظر مشتریان دارد. همچنین پس از عامل ظرافت با توجه به عوامل زیرمجموعه هر یک از شاخص‌های موردبررسی به ترتیب عوامل استفاده از مواد اولیه مناسب در ساخت مبلمان، قیمت محصولات چوبی، ارگونومی، رضایت مشتری از خرید قبلی خود و تحویل فوری و به‌موقع محصولات از مهم‌ترین عوامل تأثیرگذار در خرید مبلمان توسط مشتریان می‌باشند.}, keywords_fa = {مبلمان چوبی منزل,آزمون فریدمن,شاخص‌,خرید,مشتریان}, url = {https://www.ijwp.ir/article_11298.html}, eprint = {https://www.ijwp.ir/article_11298_fc137f87c434a97c4338a9bbc71fcd62.pdf} }